Modifications FCC | Digi 90000797_A specs

C E R T I F I C A T I O N S

FCC Part 15 Class B

device must accept any interference received, including interference that may cause undesired operation.

If the FCC ID is not visible when installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module FCC ID. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID: MCQ-50M1380, IC: 1846A-50M1380.

Modifications (FCC 15.21)

Changes or modifications to this equipment not expressly approved by Digi may void the user’s authority to operate this equipment.

Industry Canada

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.

Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.

40	Connect Wi-Wave Hardware Reference, Rev A 2/2008

Image 38

Digi 90000797_A manual Modifications FCC

Contents

Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Related UpdatesG i i n f o r m a t i o n Documentation Contact information To contact Digi International by Use About the Module A t u r e s Digi Connect Wi- Wave module edge connector A t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connector Pinout Pin Type Wlan Mini Card Signal Channel Allocations B p e r i p h e r a l c o n t r o l l e r2 1 b / g m o d e s a n d c h a n n e l s Channel Center frequency Frequency spread MHz MHz MHz L t a g e r e g u l a t o r s L t a g e m o n i t o r R e s e t g e n e r a t o r W e r Features A t ’ s o n t h e d e v e l o p m e n t b o a r d Development board Unpopulated components Digi Connect Wi-Wave module connector, J52 Pin Type Signal No connect or Jtagtdi Vcc3.3 Debug signal breakout header LEDs D s I t c h e s a n d r e s e t f u n c t i o n a l i t y Alternative methods to trigger Input power jack, J3 Input power supply W e r s u p p l y Jtag breakout Header signal mapA G B r e a k o u t H e a d e r , P 2 B p e r i p h e r a l i n t e r f a c e , J B u g b r e a k o u t h e a d e r , P 2 Debug breakout Header signal mapSignal FL cables FL connectorsL a n d R P S M a c o n n e c t o r s RP-SMA connectors For more information Using the Antenna Necessary Conditions for Integration Connect Wi-Wave antenna configurations N e r a l i n f o r m a t i o n T e n n a Specification s 2 d B i D i p o l eDimensions Attributes Antenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram T e n n a Specification s 5 d B i D i p o l e Attribute Band Radiation pattern H-Plane 2.0 and 5.0 GHz Color Freq MHz Peak dBi Angle o Avg dBi Radiation pattern E-plane 2.0 and 5.0 GHz V i r o n m e n t a l Specification s C h a n i c a l d i m e n s i o n s F e t y s t a t e m e n t s W e r r e q u i r e m e n t sE x p o s u r e s t a t e m e n t Parameter Limits Module Dimensions Development Board dimensions Appendix BCertifications C P a r t 1 5 C l a s s B Modifications FCC Declaration of Conformity International EMC Standards Standards Index Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008