B u g b r e a k o u t h e a d e r , P 2, Signal | Digi 90000797_A

A B O U T T H E D E V E L O P M E N T B O A R D

Debug breakout header, P21

D e b u g b r e a k o u t h e a d e r , P 2 1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The debug breakout header’s primary purpose is to provide access to the

W_DISABLE# signal. The W_DISABLE# signal is typically used as a hardware means to disable RF transmissions from the module without software intervention.

Debug breakout

header signal map	Pin	Type	Signal	Pin	Type	Signal

	1	Rsvd	SIM_PWR	2	Monitor pt	+3.3V_MC

	3	Rsvd	SIM_RST	4	Monitor pt	LED_WWAN#

	5	Rsvd	SIM_CLK	6	Monitor pt	GND

	7	Rsvd	SIM_Pin 4	8	Monitor pt	LED_WLAN#

	9	Rsvd	SIM_GND	10	Monitor pt	GND

	11	Rsvd	SIM_VPP	12	Monitor pt	LED_WPAN#

	13	Rsvd	SIM_DATA	14	Monitor pt	GND

	15	Rsvd	SIM_Pin 8	16	Monitor pt	RESET#

	17	n/a	No connect	18	Monitor pt	GND

	19	Monitor pt	GND	20	In	W_DISABLE#
W_DISABLE#
W_DISABLE#	The active low W_DISABLE# signal is on pin 20 of the debug breakout header. GND
signal	signals are positioned adjacent to the W_DISABLE# signal on pins 18 and 19. To

24	Connect Wi-Wave Hardware Reference, Rev A 2/2008

Image 22

Digi 90000797_A manual B u g b r e a k o u t h e a d e r , P 2, Debug breakout Header signal map, Signal

Contents

Digi Connect Wi-Wave Hardware Reference Page Contents FCC Part 15 Class B Related UpdatesG i i n f o r m a t i o n Documentation Contact information To contact Digi International by Use About the Module A t u r e s Digi Connect Wi- Wave module edge connector A t ’ s o n t h e m o d u l e ? Digi Connect Wi- Wave module edge connector Pinout Pin Type Wlan Mini Card Signal Channel Allocations B p e r i p h e r a l c o n t r o l l e r2 1 b / g m o d e s a n d c h a n n e l s Channel Center frequency Frequency spread MHz MHz MHz L t a g e r e g u l a t o r s L t a g e m o n i t o r R e s e t g e n e r a t o r W e r Features A t ’ s o n t h e d e v e l o p m e n t b o a r d Development board Unpopulated components Digi Connect Wi-Wave module connector, J52 Pin Type Signal No connect or Jtagtdi Vcc3.3 Debug signal breakout header LEDs D s I t c h e s a n d r e s e t f u n c t i o n a l i t y Alternative methods to trigger Input power jack, J3 Input power supply W e r s u p p l y A G B r e a k o u t H e a d e r , P 2 Header signal mapJtag breakout B p e r i p h e r a l i n t e r f a c e , J Signal Debug breakout Header signal mapB u g b r e a k o u t h e a d e r , P 2 L a n d R P S M a c o n n e c t o r s FL connectorsFL cables RP-SMA connectors For more information Using the Antenna Necessary Conditions for Integration Connect Wi-Wave antenna configurations N e r a l i n f o r m a t i o n T e n n a Specification s 2 d B i D i p o l eDimensions Attributes Antenna specifications 2 dBi Dipole Antenna strength radiation pattern diagram T e n n a Specification s 5 d B i D i p o l e Attribute Band Radiation pattern H-Plane 2.0 and 5.0 GHz Color Freq MHz Peak dBi Angle o Avg dBi Radiation pattern E-plane 2.0 and 5.0 GHz V i r o n m e n t a l Specification s C h a n i c a l d i m e n s i o n s F e t y s t a t e m e n t s W e r r e q u i r e m e n t sE x p o s u r e s t a t e m e n t Parameter Limits Module Dimensions Development Board dimensions Appendix BCertifications C P a r t 1 5 C l a s s B Modifications FCC Declaration of Conformity International EMC Standards Standards Index Index-44Connect Wi-Wave Hardware Reference, Rev a 2/2008 WDISABLE# signal Connect Wi-Wave Hardware Reference, Rev a 2/2008