Cabling (continued)

Digital recommends that you use repeaters to segment the ring in a network with multiple wiring closets. In some situations, only one, or no repeaters, are required. Refer to the appropriate Token Ring repeater manual for specific information.

When distances exceed the lobe lengths in Table 2, or if the MAU does not have Digital's Autowrap functionality, two repeaters are required.

When a MAU has Autowrap enabled, only one repeater is required per wiring closet if the distance between the wiring closets does not exceed the distances shown in Table 2.

With UTP level 5 cable at 4 Mb/s, no repeaters are required with multiple wiring closets if the total cable budget is within the distances shown in Table 3.

For UTP level 3 cable at 4 Mb/s, divide all distances in Table 3 by 1.3.

Table 3 Total Cable Budget for UTP Level 5 Cable at 4 Mb/s1

 

 

 

 

W i r i n g C l o s e t s

 

 

 

 

 

MAUs

0

1

2

3

4

5

6

 

1

210 m (689 ft)

206 m (675 ft)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2

192 m (630 ft)

189 m (620 ft)

185 m (607 ft)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

175 m (574 ft)

171 m (561 ft)

168 m (551 ft)

164 m (538 ft)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4

157 m (515 ft)

154 m (505 ft)

150 m (492 ft)

147 m (482 ft)

143 m (469 ft)

 

 

 

 

 

 

 

 

 

 

 

 

 

5

140 m (459 ft)

136 m (446 ft)

133 m (436 ft)

129 m (423 ft)

126 m (413 ft)

122 m (400 ft)

 

 

 

 

 

 

 

 

 

 

 

 

6

122 m (400 ft)

119 m (390 ft)

115. m (377 ft)

112 m (367 ft)

108 m (354 ft)

105 m (344 ft)

101 m (331 ft)

 

 

 

 

 

 

 

 

 

 

 

1All distances include patch cables.

Total cable budget = maximum lobe length + adjusted ring length

Adjusted ring length = total trunk length ± shortest trunk length

Shielded Twisted-Pair Cable Configuration:

Digital supports industry standards for shielded twisted-pair (STP) cable. Refer to the IBM Token Ring Network Introduction and Planning Guide for specific information on STP cable.

Cable Connector Specifications

Table 4 lists the signal names of each pin associated with the Ring In, Ring Out, and Lobe connectors. The shaded area in the table indicates signals used only by Token Ring.

Table 4 MAU Connector Signal Names

Connector

 

 

 

Pins

 

 

 

 

 

Name

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

Ring In

RS422 RX+

RS422 RX±

Transmit±

Receive+

Receive±

Transmit+

RS422 TX±

RS422 TX+

 

 

 

 

 

 

 

 

 

 

Ring Out

not used

not used

Receive±

Transmit+

Transmit±

Receive+

not used

not used

 

 

 

 

 

 

 

 

 

 

Lobe

not used

not used

Receive±

Transmit+

Transmit±

Receive+

not used

not used

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

DECmau 900TL

Page 12
Image 12
Digital Media 900TL manual Cable Connector Specifications, Total Cable Budget for UTP Level 5 Cable at 4 Mb/s1