Installation Instructions

Ensure that all packing items are removed (read any warning labels carefully).

Retain all packing for possible future use, in the event of moving or returning the appliance to your supplier. To reduce heat losses and to prevent any chimney updraught sffecting the operation of your fire we recommend that the chimney flue is blocked off, ensure that there is a slight gap for ventilation.

To install the appliance;

Place the stove against the wall and connect the stove to your electricity supply.

Plug the stove into a 13amp/240volt outlet. Before switching on the appliance, please read the following instructions.

Before using the manual controls firstly fill the water tank (See ‘Maintenance’, ‘Filling the water tank’).

Manual Controls.

The Opti-myst Manual controls are located behind the doors.

(See Fig. 2 for Manual Control lay out)

Switch ‘A’:- Controls the electricity supply to the stove.

Note: This switch must be in the ‘ON’ ( I ) position for the stove to operate with or without heat.

Switch ‘B’:- Controls the function of the fire.

Press once to turn on flame effect. This will be indicated by one beep.

Although the main lights operate immediately it will take a further 30 seconds before the flame effect starts.

Press

again to give flame effect and half heat.

This will be indicated by two beeps.

Press

again to give flame effect and full heat. This

will be indicated by three beeps.

Press

again to return to flame effect only.

This will be indicated by one beep.

Press

to put stove in to standby mode.

This will be indicated by one beep.

Control Knob ‘C’:- Controls the intensity of the flame effect.

Turning the control knob to the left increases the flame effect, turning the control knob to the right will decrease

the flame effect.

Control Knob ‘D’:- Controls the Electronic Thermostat setting.

Turning the control knob to the left will decrease the temperature setting, turning the control knob to the right will increase the temperature setting.

When the water is empty the main lamps go out. See instructions under ‘Maintenance’, ‘Filling the water tank’. When this procedure is complete, the main lamps will illuminate but it will take 30 seconds before the flames return.

Depending on room temperature and humidity there may be some condensation on the inside of the stove. This can be overcome by turning the flame control knob down and leaving the doors of the stove slightly ajar, until the glass warms up.

Electronic Thermostat

The thermostat controls the heat output according to the room temperature. This ensures that the stove will not produce heat unnecessarily when the room is warm.

To set the temperature you require, turn the thermostat control knob ‘D’ (See Fig. 2) to the right until the desired temperature is reached. Alternatively to heat a cold room quickly, turn the thermostat control knob ‘D’ (See Fig. 2) up fully. When the room has reached the desired temperature, turn the thermostat control knob ‘D’ (See Fig. 2) to the left until the desired heat setting is achieved. The stove will now automatically operate at this temperature.

Remote Control Operation

On the control panel, Switch A (see Fig. 2) must be in the ‘ON’ ( I ) position in order for the remote control to operate. There are 3 buttons on the remote control. (See Fig. 7)

To operate correctly the remote must be pointed towards the front fuel effect.

The remote control functions are as follows:

Press once to turn on Flame effect only.

This will be indicated by one beep.

Press once to turn on Half heat and Flame effect. This will be indicated by two beeps.

Press again to turn on Full heat and Flame effect. This will be indicated by three beeps.

Standby

This will be indicated by one beep.

- 2 -

Page 7 Page 9
Page 8
Image 8
Dimplex EN60555-3, EN60555-2, EN55014 To install the appliance, Manual Controls, Press, This will be indicated by two beeps
Page 7 Page 9

EN60555-3, EN60555-2, EN55014 specifications

Dimplex is a brand renowned for its commitment to innovation and efficiency in electric heating solutions. Among its product offerings, the Dimplex EN55014, EN60555-2, and EN60555-3 stand out for their adherence to rigorous standards and advanced technologies.

The Dimplex EN55014 is designed primarily for electrical appliances, ensuring they comply with essential electromagnetic compatibility requirements. This standard ensures that the appliance does not interfere with other electronic devices while maintaining optimal performance. This is crucial in today's interconnected environment, where multiple devices operate in close proximity. The EN55014 certification guarantees that Dimplex products remain reliable, fostering consumer confidence in their usage.

Moving on to the EN60555-2 standard, it focuses on reducing the harmonic currents generated by electrical equipment. Harmonics can lead to inefficiencies and potential damage to electrical networks. The Dimplex range offers solutions that are designed to minimize these harmonics, contributing to improved system stability and reducing energy losses. By complying with this standard, Dimplex products promote a cleaner energy environment, which is essential for both residential and commercial applications.

The EN60555-3 standard extends the assessment of harmonics, specifically addressing the limits of voltage distortion in public power systems. This is vital to ensure that the power supply remains stable and reliable. Dimplex products have incorporated technologies that keep them well within these limits, ensuring minimal disturbance to the wider electrical grid. This feature is particularly significant for businesses and infrastructures reliant on consistent power levels, as it helps prevent outages and equipment failure.

In summary, the Dimplex EN55014, EN60555-2, and EN60555-3 certifications represent a commitment to quality and efficiency. By focusing on electromagnetic compatibility and minimizing harmonic distortions, Dimplex ensures that its products not only excel in performance but also contribute positively to the broader electrical ecosystem. These features make Dimplex an ideal choice for consumers and commercial operators looking for reliable, innovative heating solutions that prioritize sustainability and efficiency. Dimplex continues to lead in implementing standards that protect both users and the environments in which they operate.
Top Page Image Contents