Dixi XWA11V manual Parameter List, Eal

dIXEL			Operating Instructions XWA11V	1598003200
14.	PARAMETER LIST
Ot		Thermostat probe calibration: (-12.0⎟12.0°C/ -21⎟21°F) allows to adjust possible offset of the
		thermostat probe.
CF		T measurement unit: °C = Celsius; °F = Fahrenheit. When the measurement unit is changed the Set
		Point and the values of some parameters have to be modified.
rES		Resolution (for °C): (in = 1°C; dE = 0.1 °C) allows decimal point display.
Ut		Display update: The time delay of the T readout (0÷255s)
onF		Off function enabling: n = off function disabled; y = off function enabled;
ALU		High T° alarm setting: (ALL ⎟ 150°C or 302°F);
		when this T° is reached and after the ALd delay time the HA alarm is enabled.
ALL		Low T° alarm setting: (- 50°C or -58°F ⎟ ALU)
		when this T° is reached and after the ALd delay time, the LA alarm is enabled,.
AFH		T° alarm differential: (0,1÷25,5°C; 1÷45°F) differential for T° alarm Set Point and fan regulation Set
		Point, always a positive value
ALd		T° alarm delay: (0÷255 min) time interval between the detection of an alarm condition and the
		corresponding alarm signaling.
dAO		Delay of T° alarm at start-up: (0min÷23h 50min) time interval between the detection of the T° alarm
		condition after the instrument power on and the alarm signaling.
EdA		Alarm delay at the end of defrost: (0⎟255 min) Time interval between the detection of the T° alarm
		condition at the end of defrost and the alarm signaling.
dot		Delay of T° alarm after closing the door: (0⎟255 min) Time delay to signal the T° alarm		condition
		after closing the door.
LHt		Light timer: (0-255 min) The time the light will stay on after pressing the light switch on the keyboard.
doA		Open door alarm delay:(0÷255 min) delay between the detection of the open door condition and its
		alarm signaling: the flashing message “dA” is displayed.
oA1		First relay configuration:	(14-15): ALr = alarm; LHt = light; onF = on/off relay
oA2		Second relay configuration: (14-16): ALr = alarm; LHt = light; onF = on/off relay
AOP		Alarm relay polarity: cL = closing contacts; oP = opening contacts.
i1P		Digital input 1 polarity (1-2): CL : the digital input is activated by closing the contact;
OP		the digital input is activated by opening the contact
i1L		Door switch to turn light ON(1-2):(y / no) To turn the light ON automatically when the door is open.
		The light will turn off based on LHt . Keyboard switch must be turned ON first.
i1F		Digital input 1 operating mode(1-2): EAL = external alarm; dor = door switch; dFr = A defrost is
		running; LHt = keep light ON (signal from occupancy sensor) override LHt.;
i2P		Digital input 2 polarity (1-3): CL : the digital input is activated by closing the contact;
OP		the digital input is activated by opening the contact
i2F		Digital input 2 operating mode: configure the digital input function:
EAL		= External alarm;
PAn		=Panic alarm;
dFr = A defrost is running;
LHt = Keep light ON (signal from occupancy sensor) override LHt.
did		Time interval/delay for digital input alarm:(0⎟255 min.) If I2F=EAL or PAn (external alarms), “did”
		parameter defines the time delay between the detection and the successive signaling of the alarm.
tbA		Alarm relay & Buzzer disabling: (y ; no)
Pbc		Type of probe (PTC, NTC)
dP1		Probe 1 T
rEL		Software release for internal use.
Ptb		Parameter table code: read only.

Weiss Instruments, Inc. 905 Waverly Ave. Holtsville, NY 11742 631-207-1200 www.weissinstruments.com 8