DKS Enterprises 1812 PLUS

2.6 Miscellaneous

2.6.1 Restore Defaults

This step will restore the factory set defaults for each of the programming parameters.

WARNING: Once started, this sequence will program all values to factory default.

1. Press * 9 0 and enter the MASTER CODE. [ * 9 0 _ _ _ _ (beep)]

2. Press 9 9 9 9 then press *. [ 9 9 9 9 * (beep)]

3. This sequence will end itself automatically. [beeeeeep]

Page 36 1812-161-E-1-10

Contents

Main Owners Manual Page Use this manual with the following models only. Table of Contents Preface Section 1 Installation & Wiring Section 2 Programming Section 3 Adjustments Section 4 User Instructions Section 5 Maintenance and Trouble Shooting Important Notices FCC United States DOC - Canada Notice: Notice: General Information Features SECTION 1 - INSTALLATION 1.1 Mount the 1812 Plus 1.2 Mount the By-Pass Switch 1.3 Dimensions Surface Mount Surface Mount Curved Flush Mount Rough-in Box Flush Mount Page 12 1812-161-E-1-10 Page 1.4 Telephone Line Wiring 1.5 Power Wiring 1.6 Surge Suppression and Grounding 1.7 Wiring for a Single Unit Telephone Mode GND Page 16 1812-161-E-1-10 A A B This device is powered by a 16.5 VAC transformer. DO NOT power this device with a C 1.8 Wiring for Multiple Units Telephone Mode GND 1st 1812 2nd 1812 ENTRY BY-PASS A This device is powered by a 16.5 VAC transformer. DO NOT power this device with a 1.10 Wiring for Multiple Units Intercom Mode 1st 1812 2nd 1812 B This device is powered by a 16.5 VAC transformer. DO NOT power this device with a 1.11 Main Terminal Description SECTION 2 PROGRAMMING Before You Start Programming Guide Table 2.1 Programming Information 2.1.1 Programming from the Keypad 2.1.2 Programming with a Touch-Tone Telephone 2.2 System Parameter Programming 2.2.1 Phone / Intercom Mode 2.2.2 Single or Multiple Systems 2.2.3 System Attention Number 2.2.4 Single or Double Ring 2.2.5 Number of Rings to Ring Residence 2.2.6 Talk Time 2.2.7 Relay Strike Time 2.2.8 Tone Open Numbers 2.2.9 Answer Incoming Call on X Rings 2.2.10 Hang Up Tone 2.2.11 Call Waiting 2.2.12 Turn Speaker On 2.2.13 Set Call Forwarding Microphone Gain and Speaker Volume 2.3 Directory Codes 2.3.1 Directory Codes 24 50 Dial Phone Number 2.3.2 Delete Phone Number from Directory Codes 24 - 50 2.3.3 Delete All Phone Numbers from Directory Codes 24 - 50 2.4 Devices 2.4.1 Simple Access Code Programming 2.4.2 Access Code Programming 2.4.3 Delete Access Codes 2.4.4 Delete All Access Codes 2.4.5 Temporary Access Code Programming 2.4.6 Delete Temporary Access Codes 2.4.7 Delete All Temporary Access Codes 2.5 Time Functions 2.5.1 Program Calendar Chip 2.5.2 Call Forward Time 2.5.3 Call Forward Phone Number Programming 2.5.4 Do Not Disturb Schedule 2.5.5 Relay Hold Schedule 2.5.6 Time Zones Page SECTION 3 ADJUSTMENTS Speaker Volume Microphone Gain Page SECTION 4 USER INSTRUCTIONS 4.1 Resident Operating Instructions 4.1.1 Granting or Denying a Guest Access 4.1.2 Call Waiting 4.1.3 Dial-Out Phone Numbers 4.1.4 Access Codes 4.2 Remote Operation 4.2.1 Remote Programming 4.2.2 Remote Relay Activation 4.2.3 Relay Activation 4.2.4 Relay Activation Check SECTION 5 MAINTENANCE 5.1 Troubleshooting 5.2 Phone Line Polarity Bypass Switch 1812 Terminal Surge Suppresser 5.3 Isolating Noise Problems 5.4 Troubleshooting Tables SYMPTOM POSSIBLE SOLUTION(S) SYMPTOM POSSIBLE SOLUTION(S) 5.5 Wire Diagram 5.6 Accessories 5.7 Tables Directory Codes / Dial-Out Phone Numbers Access Code Log Sheet