Manuals / Eagle Home Products / Household Appliance / Smoke Alarm

Eagle Home Products Eagle Series Peak Screen, Elapsed Time Screen, To enter a user and station ID

Models: Eagle Series

1 80

Download 80 pages 15.42 Kb

Page 26

To enter a user and station ID:

To scroll to the next screen at any time, press the DISP/ADJ button.

1.Press the POWER/ENTER button. The ﬁrst character under USER ID ﬂashes (* is default).

2.Press the AIR/▲ and SHIFT/▼ buttons to scroll through the available characters. (The asterisk and blank space are between the set of letters and numbers.)

3.When the desired character displays, press the POWER/ENTER button to enter the character and go to the next character.

4.Repeat steps 2 and 3 for the remaining 19 characters.

After you enter the last character, the Peak screen displays.

Peak Screen

The Peak screen displays the highest (lowest for O2) concentrations

detected since the Eagle was turned on. Peak readings are stored in the Eagle’s memory until a higher level is detected or the Eagle is turned off.

The Lunchbreak “RESUME” option enables the Eagle to remember peak readings when it is turned off. See “Starting Up the Eagle” on page 9.

Elapsed Time Screen

The Elapsed Time screen displays the time in minutes since the Eagle was last turned on.

20 • Display Mode

Eagle Instruction Manual

Image 26

Eagle Home Products Eagle Series instruction manual Peak Screen, Elapsed Time Screen, To enter a user and station ID

Contents

Portable Multi-Gas Detector RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510Warranty WarrantyTable of Contents Display Mode Table of ContentsCalibration Appendix F Eagle Tank Tester Model Introduction IntroductionOverview About this Manual Eagle Speciﬁcations SpecificationsSpeciﬁcations Carbon Standard Sensor SpeciﬁcationsCombustible Oxygen Control Panel DescriptionCase ButtonsInterface Port Alarm LightsBattery Charger Connector BuzzerSensors Circuit Boards Methane Elimination SwitchCAL/SETUP Switch Operation OperationStarting Up the Eagle Operation Normal Operation Monitoring Combustible Gas in the PPM RangeTarget Gas LEL Factor Full Response Mode Conversion Factors Methane CalibrationMonitoring Combustible Gases Other than Methane Setting User Access Turning Off the EagleAlarms AlarmsAlarm Indications Stel alarm toxics only Low ﬂow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms User and Station ID Screen Display ModeDisplay Mode To enter a user and station ID Peak ScreenElapsed Time Screen Date/Time Screen Battery Voltage ScreenTWA/STEL Screen To clear the data log Clear Data Logger ScreensRemaining Log Time Screen Setup Mode Setup ModeTips for Using Setup Mode Entering Setup Mode Updating the Battery Type SettingUpdating Channel Settings Setting a custom target gas label Fullscale PPM Readings Equivalent to 100% LEL Target GasUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Lunch Break Setting Updating the Eagle’s Serial NumberUpdating the Alarm Latching Setting Updating the Alarm Silence SettingUpdating the Auto Calibration Settings Turning the User ID Function On or OffUpdating the Back Light Setting Turning the Auto Fresh Air Function On or OffUpdating the Interval Time Setting data log option Updating Log Data Over Write Setting data log optionUpdating the Time Calibration Setting data log option Updating the Date and Time Settings data log optionReturning to Default Settings Updating the Zero Follow SettingsUpdating the Conﬁrmation Beep Setting To reset the oxygen zero setting To reset all default settingsTo reset all default alarm point settings Preparing for Calibration CalibrationCalibration Supplies and Equipment CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration To display the battery voltage MaintenanceDisplaying the Battery Voltage Replacing Alkaline BatteriesReplacing Sensors To replace the combustibles sensorTo replace the oxygen sensor To replace the H2S or CO sensor Appendix a Parts List Appendix a Parts ListParts List Part Number DescriptionPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Description Appendix C Non-Standard Toxic Gas SensorsSpeciﬁcations Non-Standard Toxic Gas Sensors SpeciﬁcationsCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Parts List Non-Standard Toxic Gas SensorsCarbon Dioxide Sensor Speciﬁcations Alarm TWA Alarm Stel AlarmAppendix D Carbon Dioxide Sensors Appendix D Carbon Dioxide SensorsCalibrating Carbon Dioxide Sensors Normal Operation of Carbon Dioxide SensorsDemand Zero for Carbon Dioxide Sensors Carbon Dioxide Fresh Air ReadingsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Parts List Carbon Dioxide SensorsTarget Gases Range Alarm TWA Alarm Stel AlarmAppendix E Infrared Methane Sensors Infrared Methane Sensor SpeciﬁcationsCalibrating Infrared Methane Sensors Sensor Analog PCB SocketParts List Infrared Methane Sensors Replacing Infrared Methane SensorsTo use the ﬂoat probe assembly Appendix F Eagle Tank Tester ModelTo attach the dilution ﬁtting AlarmsTo eliminate an oxygen alarm that is not being used Appendix F Eagle Tank Tester ModelParts List Eagle Tank Tester Model CalibrationAppendix G Five-Gas and Six-Gas Models Appendix G Five-Gas and Six-Gas ModelsDisplaying Additional Channels Alarms Calibration, Display, and Setup ModesAppendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board