Manuals / Eagle Home Products / Household Appliance / Smoke Alarm

Eagle Home Products Eagle Series Updating the Time Calibration Setting data log option

Models: Eagle Series

1 80

Download 80 pages 15.42 Kb

Page 44

1.From the main menu, select the LOG DATA OVER WRITE menu option.

2.Press the AIR/▲ or SHIFT/▼ button to display the desired setting.

3.Press the POWER/ENTER button to enter the setting and return to the main menu.

Updating the Time Calibration Setting (data log option)

This setting indicates how often the Eagle alerts you to needed calibration. The minimum setting is 1 day; the maximum setting is 180 days. The default setting is “off”.

Tip: Press and hold the AIR/▲ or SHIFT/▼ button to rapidly scroll through settings.

1.From the main menu, select the TIME CALIBRATION menu option.

2.Press the AIR/▲ and SHIFT/▼ buttons to display the desired setting.

3.Press the POWER/ENTER button to enter the setting and return to the main menu.

Updating the Date and Time Settings (data log option)

The Data Logger uses the data and time to identify entries.

1.From the main menu, select the DATE/TIME menu option.

2.Press the AIR/▲ or SHIFT/▼ button to display the desired month.

38 • Setup Mode

Eagle Instruction Manual

Image 44

Eagle Home Products Eagle Series instruction manual Updating the Time Calibration Setting data log option

Contents

Portable Multi-Gas Detector RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510Warranty WarrantyTable of Contents Display Mode Table of ContentsCalibration Appendix F Eagle Tank Tester Model Introduction IntroductionOverview About this Manual Eagle Speciﬁcations SpecificationsSpeciﬁcations Carbon Standard Sensor SpeciﬁcationsCombustible Oxygen Description CaseControl Panel ButtonsAlarm Lights Battery Charger ConnectorInterface Port BuzzerSensors Circuit Boards Methane Elimination SwitchCAL/SETUP Switch Operation OperationStarting Up the Eagle Operation Normal Operation Monitoring Combustible Gas in the PPM RangeTarget Gas LEL Factor Full Response Mode Conversion Factors Methane CalibrationMonitoring Combustible Gases Other than Methane Setting User Access Turning Off the EagleAlarms AlarmsAlarm Indications Stel alarm toxics only Low ﬂow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms User and Station ID Screen Display ModeDisplay Mode To enter a user and station ID Peak ScreenElapsed Time Screen Date/Time Screen Battery Voltage ScreenTWA/STEL Screen To clear the data log Clear Data Logger ScreensRemaining Log Time Screen Setup Mode Setup ModeTips for Using Setup Mode Entering Setup Mode Updating the Battery Type SettingUpdating Channel Settings Setting a custom target gas label Fullscale PPM Readings Equivalent to 100% LEL Target GasUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Lunch Break Setting Updating the Eagle’s Serial NumberUpdating the Alarm Latching Setting Updating the Alarm Silence SettingUpdating the Auto Calibration Settings Turning the User ID Function On or OffUpdating the Back Light Setting Turning the Auto Fresh Air Function On or OffUpdating the Interval Time Setting data log option Updating Log Data Over Write Setting data log optionUpdating the Time Calibration Setting data log option Updating the Date and Time Settings data log optionReturning to Default Settings Updating the Zero Follow SettingsUpdating the Conﬁrmation Beep Setting To reset the oxygen zero setting To reset all default settingsTo reset all default alarm point settings Calibration Calibration Supplies and EquipmentPreparing for Calibration CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Maintenance Displaying the Battery VoltageTo display the battery voltage Replacing Alkaline BatteriesReplacing Sensors To replace the combustibles sensorTo replace the oxygen sensor To replace the H2S or CO sensor Appendix a Parts List Parts ListAppendix a Parts List Part Number DescriptionPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Appendix C Non-Standard Toxic Gas Sensors SpeciﬁcationsDescription Non-Standard Toxic Gas Sensors SpeciﬁcationsCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Parts List Non-Standard Toxic Gas SensorsAlarm TWA Alarm Stel Alarm Appendix D Carbon Dioxide SensorsCarbon Dioxide Sensor Speciﬁcations Appendix D Carbon Dioxide SensorsNormal Operation of Carbon Dioxide Sensors Demand Zero for Carbon Dioxide SensorsCalibrating Carbon Dioxide Sensors Carbon Dioxide Fresh Air ReadingsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Parts List Carbon Dioxide SensorsRange Alarm TWA Alarm Stel Alarm Appendix E Infrared Methane SensorsTarget Gases Infrared Methane Sensor SpeciﬁcationsCalibrating Infrared Methane Sensors Sensor Analog PCB SocketParts List Infrared Methane Sensors Replacing Infrared Methane SensorsTo use the ﬂoat probe assembly Appendix F Eagle Tank Tester ModelAlarms To eliminate an oxygen alarm that is not being usedTo attach the dilution ﬁtting Appendix F Eagle Tank Tester ModelParts List Eagle Tank Tester Model CalibrationAppendix G Five-Gas and Six-Gas Models Appendix G Five-Gas and Six-Gas ModelsDisplaying Additional Channels Alarms Calibration, Display, and Setup ModesAppendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board