Manuals / Eagle Home Products / Household Appliance / Smoke Alarm

Eagle Home Products Eagle Series instruction manual Updating Channel Settings

Models: Eagle Series

1 80

Download 80 pages 15.42 Kb

Page 31

Updating Channel Settings

This procedure describes how to update channel settings for the combustible gas, oxygen, and toxic gas channels.

CAUTION:Verify that the correct sensor is installed before you update a channel’s settings.

Updating combustible gas channel settings

This section describes how to update the target gas label, set a custom gas label, and update the fullscale PPM setting for the combustible gas channel.

Updating the target gas label

1.From the main menu, select the GAS COMBINATIONS menu option.

2.Use the AIR/▲ or SHIFT/▼ button to place the prompt next to the combustible gas channel (in this example CH4).

3.Press the POWER/ENTER button. The combustible gas target gas label ﬂashes. This indicates that this setting can now be updated.

4.Press the AIR/▲ or SHIFT/▼ buttons to display the available combustible gas target gas labels (CH4, HEX, H2, ***, and NOT USED).

NOTE: Select the HEX or *** setting for Methane Elimination

(see “Appendix B: Methane Elimination” on page 52 for more information.)

5.Press the POWER/ENTER button to enter the new target gas label.

A screen displays that shows the fullscale PPM setting, which corresponds to 100% LEL, and display increments for the target gas label you selected. If you select *** as the gas label, you must update the fullscale PPM setting to correspond to 100% LEL for the target gas.

Eagle Instruction Manual

Setup Mode • 25

Image 31

Eagle Home Products Eagle Series instruction manual Updating Channel Settings

Contents

RKI Instruments, Inc Whipple Rd. Hayward, CA 94544 510 Portable Multi-Gas DetectorWarranty WarrantyTable of Contents Table of Contents Display ModeCalibration Appendix F Eagle Tank Tester Model Overview IntroductionIntroduction About this Manual Speciﬁcations SpecificationsEagle Speciﬁcations Combustible Oxygen Standard Sensor SpeciﬁcationsCarbon Buttons DescriptionCase Control PanelBuzzer Alarm LightsBattery Charger Connector Interface PortSensors CAL/SETUP Switch Methane Elimination SwitchCircuit Boards Starting Up the Eagle OperationOperation Operation Monitoring Combustible Gas in the PPM Range Normal OperationMonitoring Combustible Gases Other than Methane Full Response Mode Conversion Factors Methane CalibrationTarget Gas LEL Factor Turning Off the Eagle Setting User AccessAlarm Indications AlarmsAlarms Stel alarm toxics only Low ﬂow alarm Sensor failure alarm and emergency operation Resetting Gas Alarms Display Mode Display ModeUser and Station ID Screen Elapsed Time Screen Peak ScreenTo enter a user and station ID TWA/STEL Screen Battery Voltage ScreenDate/Time Screen Remaining Log Time Screen Clear Data Logger ScreensTo clear the data log Tips for Using Setup Mode Setup ModeSetup Mode Updating the Battery Type Setting Entering Setup ModeUpdating Channel Settings Setting a custom target gas label Target Gas Fullscale PPM Readings Equivalent to 100% LELUpdating oxygen channel settings Updating toxics channel settings Setting a custom target gas label Updating Combustible Gas Channel Units of Measure Updating the Alarm Point Settings Updating the Eagle’s Serial Number Updating the Lunch Break SettingUpdating the Alarm Silence Setting Updating the Alarm Latching SettingTurning the User ID Function On or Off Updating the Auto Calibration SettingsTurning the Auto Fresh Air Function On or Off Updating the Back Light SettingUpdating Log Data Over Write Setting data log option Updating the Interval Time Setting data log optionUpdating the Date and Time Settings data log option Updating the Time Calibration Setting data log optionUpdating the Conﬁrmation Beep Setting Updating the Zero Follow SettingsReturning to Default Settings To reset all default alarm point settings To reset all default settingsTo reset the oxygen zero setting Calibration CalibrationCalibration Supplies and Equipment Preparing for CalibrationCalibrating the Eagle Calibration Calibrating with the Single Calibration method Calibration Replacing Alkaline Batteries MaintenanceDisplaying the Battery Voltage To display the battery voltageTo replace the combustibles sensor Replacing SensorsTo replace the oxygen sensor To replace the H2S or CO sensor Part Number Description Appendix a Parts ListParts List Appendix a Parts ListPart Number Appendix B Methane Elimination Appendix B Methane EliminationMonitoring combustible gases other than hexane Non-Standard Toxic Gas Sensors Speciﬁcations Appendix C Non-Standard Toxic Gas SensorsSpeciﬁcations DescriptionCalibrating Non-Standard Toxic Gas Sensors Adjusting the sensor controls Replacing Non-Standard Toxic Gas Sensors Parts List Non-Standard Toxic Gas Sensors Parts ListAppendix D Carbon Dioxide Sensors Alarm TWA Alarm Stel AlarmAppendix D Carbon Dioxide Sensors Carbon Dioxide Sensor SpeciﬁcationsCarbon Dioxide Fresh Air Readings Normal Operation of Carbon Dioxide SensorsDemand Zero for Carbon Dioxide Sensors Calibrating Carbon Dioxide SensorsAdjusting the sensor controls Replacing Carbon Dioxide Sensors Parts List Carbon Dioxide Sensors Parts ListInfrared Methane Sensor Speciﬁcations Range Alarm TWA Alarm Stel AlarmAppendix E Infrared Methane Sensors Target GasesSensor Analog PCB Socket Calibrating Infrared Methane SensorsReplacing Infrared Methane Sensors Parts List Infrared Methane SensorsAppendix F Eagle Tank Tester Model To use the ﬂoat probe assemblyAppendix F Eagle Tank Tester Model AlarmsTo eliminate an oxygen alarm that is not being used To attach the dilution ﬁttingCalibration Parts List Eagle Tank Tester ModelDisplaying Additional Channels Appendix G Five-Gas and Six-Gas ModelsAppendix G Five-Gas and Six-Gas Models Calibration, Display, and Setup Modes AlarmsAppendix H Eagle Transformer Gas Tester Model Appendix H Eagle Transformer Gas Tester ModelAlarms Appendix I Installing the Data Logger Board Appendix I Installing the Data Logger Board