Manuals / Edimax Technology / Computer Equipment / Network Router

Edimax Technology Multi-Homing Broadband Router manual PPPoE, Pptp, 1.5 L2TP, Telstra Big Pond

Models: Multi-Homing Broadband Router

1 87

Page 17

1.3 PPPoE	Your ISP requires you to use a Point-to-Point Protocol over
	Ethernet (PPPoE) connection.
1.4 PPTP	Your ISP requires you to use a Point-to-Point Tunneling Protocol
	(PPTP) connection.
1.5 L2TP	Your ISP requires you to use a Layer Two Tunneling Protocol
	(PPTP) connection.
1.4 Telstra Big Pond	This Protocol only used for Australia’s ISP connection.

Click on one of the WAN type and then proceed to the manual’s relevant sub-section (1.1, 1.2, 1.3, 1.4, 1.5 or 1.6). Click on Back to return to the previous screen.

1.1 Cable Modem

Choose Cable Modem if ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name and MAC address (see screen below).

Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet.

Page 17

Image 17

Edimax Technology Multi-Homing Broadband Router manual PPPoE, Pptp, 1.5 L2TP, Telstra Big Pond, Cable Modem

Contents

User Manual Multi-Homing Broadband RouterSetup Diagram FeaturesStep 2 Broadband Type 2.4.3 Special Applications2.5.3 DoS Denial of Service 2.5.1 Access ControlConfiguration Tools 4.2 Firmware UpgradePackage Content FeaturesIntroduction Minimum Requirements3 Reset Get to know the Broadband Router Back Panel1 Local Area Network LAN 2 Wide Area Network WANFront Panel Figure 1.2 below shows a typical setup for a Local Area Network LAN Setup DiagramConfigure your PC to obtain an IP address automatically Getting startedDNS Configuration Select Disable DNS WINS Configuration Select Disable WINS Resolution3 In the Local Area Connection window, click the Properties button 2b Windows2c Windows NT IP Address Select Obtain an IP address from a DHCP server Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter General Setup Chapter Quick Setup Wizard ChapterStatus Information Chapter Tools ChapterLogout Tools ChapterEnable Daylight Savings Quick SetupChapter Step 1 Time ZoneStep 2 Broadband Type End Daylight Savings TimeMenu Description1.4 PPTP 1.3 PPPoE1.5 L2TP 1.4 Telstra Big PondIf your ISP requires a Host Name, type in the host name 1.2 Fixed-IP xDSLThis is the IP address that your ISP has given you 1.3 PPPoETHE ROUTER WHEN YOU FINISHED USING THE INTERNET 1.4 PPTP Password 1.5 L2TP Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3IP Address Password 1.6 Telstra Big PondParameter DescriptionThe IP of the Login Server Login Servermanually server manuallyChapter General Settings2.2 WAN 2.1 System2.3 LAN 2.4 NAT2.1.1 Time Zone System Settingsdefault time server did not work 2.1.2 Password SettingsYou can manually assign time server address if the End Daylight Savings Time2.1.3 Remote Management Confirmed PasswordHost Address 2.2.1 Dynamic IP address 2.2 WAN2.2.2 Static IP address 2.2.3 PPPoE2.2.9 DNS 2.2.8 QoS2.2.10 DDNS 2.2.1 Dynamic IPParameter Gateway 2.2.6 Telstra Big Pond PasswordParameter Description2.2.7 WAN Policy 2.2.8 QoS The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or downEnable/Disable QoS Add a QoS rule into the table rule and click “Move Down” to make its priority lower QoS RuleThe name of this rule Select the WAN ports that the packets matchingSource Address BandwidthSource MAC Address Source IP AddressApply Reset2.2.9 DNS ParametersDomain Name Server DNS address DefaultSecondary DNS Address optional 2.2.10 DDNSPassword/Key Enable/DisableProvider DynDNSLAN IP 2.3 LANLease Time IP Address PoolDomain Name 192.168.2.100 to End IP 192.168.2.199 . If you2.4 NAT 2.4.1 Port Forwarding “WAN Port” and Comment of the setting to be The description of this settingForwarding setting will be added into the settings from the Current Port Forwarding2.4.2 Virtual Server Public Port Example Virtual Server 2.4.3 Special Applications Example Example Special ApplicationsDefault 2.4.4 UPnPUPnP Feature ParametersParametersDescription 2.4.5 Protocol and Port BindingAdd a Rule 2.4.7 Static Routing 2.4.6 ALG SettingsStatic Routing function is default disabled. You Enable Static Routinghave to enable the Static Routing function before Default Gatewayrule of Static Routing will be added into the Static 2.5 Firewall If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Filter client PCs by IP2.5.1 Access Control Add PC Client PC IP Address Example Access Control 2.5.2 URL Blocking 2.5.3 DoS Denial of Service Parameters Intrusion Detection FeatureDescription Ping of Death2.5.4 DMZ Note DMZ function works only when the NAT function is enabledClient PC IP Address 3.1 Status and Information Shows the router’s system information ChapterStatus You can see the router’s system information such as the router’s 3.1 Status and InformationHardware version, Boot code Version, Runtime code Version the Primary DNS and Secondary DNS being used 3.2 Internet ConnectionServer 3.3 Device StatusThis page shows the current system log of the Broadband router 3.4 System Log3.5 Security Log updated situation 3.6 Active DHCP ClientThis page shows all DHCP clients LAN PCs currently connected to your network. The “Active DHCP Client Table”Shows the counters of packets sent and received on WAN and 3.7 StatisticsTool You can reset the router’s system should any problem existChapter 4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Reset4.2 Firmware Upgrade some way stops functioning, you can perform a reset. Your Resetsettings will not be changed. To perform the reset, click on the The reset will be complete when the power light stops blinkingAppendix A How to Manually find your PC’s IP and MAC addressGlossary Protocol ApplicationPort Number Telnet