Manuals / Edimax Technology / Computer Equipment / Network Router

Edimax Technology Multi-Homing Broadband Router manual IP Address Pool, Lease Time, Domain Name

Models: Multi-Homing Broadband Router

1 87

Page 47

	same subnet as this broadband router if you
	want the router to be your LAN client’s default
	gateway
Lease Time	The DHCP when enabled will temporarily give
	your LAN clients an IP address. In the Lease
	Time setting you can specify the time period that
	the DHCP lends an IP address to your LAN
	clients. The DHCP will change your LAN client’s
	IP address when this time threshold period is
	reached
IP Address Pool	You can select a particular IP address range for
	your DHCP server to issue IP addresses to your
	LAN Clients.
	Note: By default the IP range is from: Start IP
	192.168.2.100 to End IP 192.168.2.199. If you
	want your PC to have a static/fixed IP address
	then you’ll have to choose an IP address outside
	this IP address Pool
Domain Name	You can specify a Domain Name for your LAN

Click <Apply> at the bottom of the screen to save the above configurations. You can now configure other advance sections or start using the router (with the advance settings in place)

Page 47

Image 47

Edimax Technology Multi-Homing Broadband Router IP Address Pool, Lease Time, Domain Name, to End IP 192.168.2.199 . If you

Contents

User Manual Multi-Homing Broadband Router2.4.3 Special Applications FeaturesSetup Diagram Step 2 Broadband Type4.2 Firmware Upgrade 2.5.1 Access Control2.5.3 DoS Denial of Service Configuration ToolsMinimum Requirements FeaturesPackage Content Introduction2 Wide Area Network WAN Get to know the Broadband Router Back Panel3 Reset 1 Local Area Network LANFront Panel Figure 1.2 below shows a typical setup for a Local Area Network LAN Setup DiagramWINS Configuration Select Disable WINS Resolution Getting startedConfigure your PC to obtain an IP address automatically DNS Configuration Select Disable DNS3 In the Local Area Connection window, click the Properties button 2b Windows2c Windows NT IP Address Select Obtain an IP address from a DHCP server Status Information Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Tools Chapter Quick Setup Wizard ChapterGeneral Setup Chapter Status Information ChapterLogout Tools ChapterStep 1 Time Zone Quick SetupEnable Daylight Savings ChapterDescription End Daylight Savings TimeStep 2 Broadband Type Menu1.4 Telstra Big Pond 1.3 PPPoE1.4 PPTP 1.5 L2TPIf your ISP requires a Host Name, type in the host name 1.2 Fixed-IP xDSLThis is the IP address that your ISP has given you 1.3 PPPoETHE ROUTER WHEN YOU FINISHED USING THE INTERNET 1.4 PPTP Password 1.5 L2TP Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3IP Address Description 1.6 Telstra Big PondPassword Parameterserver manually Login ServerThe IP of the Login Server manuallyChapter General Settings2.4 NAT 2.1 System2.2 WAN 2.3 LAN2.1.1 Time Zone System SettingsEnd Daylight Savings Time 2.1.2 Password Settingsdefault time server did not work You can manually assign time server address if the2.1.3 Remote Management Confirmed PasswordHost Address 2.2.3 PPPoE 2.2 WAN2.2.1 Dynamic IP address 2.2.2 Static IP address2.2.1 Dynamic IP 2.2.8 QoS2.2.9 DNS 2.2.10 DDNSParameter Gateway Description Password2.2.6 Telstra Big Pond Parameter2.2.7 WAN Policy 2.2.8 QoS The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or downEnable/Disable QoS Add a QoS rule into the table Select the WAN ports that the packets matching QoS Rulerule and click “Move Down” to make its priority lower The name of this ruleSource IP Address BandwidthSource Address Source MAC AddressParameters ResetApply 2.2.9 DNS2.2.10 DDNS DefaultDomain Name Server DNS address Secondary DNS Address optionalDynDNS Enable/DisablePassword/Key ProviderLAN IP 2.3 LAN192.168.2.100 to End IP 192.168.2.199 . If you IP Address PoolLease Time Domain Name2.4 NAT 2.4.1 Port Forwarding settings from the Current Port Forwarding The description of this setting“WAN Port” and Comment of the setting to be Forwarding setting will be added into the2.4.2 Virtual Server Public Port Example Virtual Server 2.4.3 Special Applications Example Example Special ApplicationsParameters 2.4.4 UPnPDefault UPnP FeatureParametersDescription 2.4.5 Protocol and Port BindingAdd a Rule 2.4.7 Static Routing 2.4.6 ALG SettingsDefault Gateway Enable Static RoutingStatic Routing function is default disabled. You have to enable the Static Routing function beforerule of Static Routing will be added into the Static 2.5 Firewall If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services Filter client PCs by IP2.5.1 Access Control Add PC Client PC IP Address Example Access Control 2.5.2 URL Blocking 2.5.3 DoS Denial of Service Ping of Death Intrusion Detection FeatureParameters Description2.5.4 DMZ Note DMZ function works only when the NAT function is enabledClient PC IP Address 3.1 Status and Information Shows the router’s system information ChapterStatus You can see the router’s system information such as the router’s 3.1 Status and InformationHardware version, Boot code Version, Runtime code Version the Primary DNS and Secondary DNS being used 3.2 Internet ConnectionServer 3.3 Device StatusThis page shows the current system log of the Broadband router 3.4 System Log3.5 Security Log connected to your network. The “Active DHCP Client Table” 3.6 Active DHCP Clientupdated situation This page shows all DHCP clients LAN PCs currentlyShows the counters of packets sent and received on WAN and 3.7 StatisticsTool You can reset the router’s system should any problem existChapter 4.1 Configuration Tools This page allows you to upgrade the router’s firmware 4.3 Reset4.2 Firmware Upgrade The reset will be complete when the power light stops blinking Resetsome way stops functioning, you can perform a reset. Your settings will not be changed. To perform the reset, click on theAppendix A How to Manually find your PC’s IP and MAC addressGlossary Telnet ApplicationProtocol Port Number

Lease Time

IP Address Pool

192.168.2.100 to End IP 192.168.2.199. If you

Domain Name