Contents
User Manual
Multi-Homing Broadband Router
Setup Diagram
Features
Step 2 Broadband Type
2.4.3 Special Applications
2.5.3 DoS Denial of Service
2.5.1 Access Control
Configuration Tools
4.2 Firmware Upgrade
Package Content
Features
Introduction
Minimum Requirements
3 Reset
Get to know the Broadband Router Back Panel
1 Local Area Network LAN
2 Wide Area Network WAN
Front Panel
Figure 1.2 below shows a typical setup for a Local Area Network LAN
Setup Diagram
Configure your PC to obtain an IP address automatically
Getting started
DNS Configuration Select Disable DNS
WINS Configuration Select Disable WINS Resolution
3 In the Local Area Connection window, click the Properties button
2b Windows
2c Windows NT
IP Address Select Obtain an IP address from a DHCP server
Status Information Chapter
Quick Setup Wizard Chapter
General Setup Chapter
General Setup Chapter
Quick Setup Wizard Chapter
Status Information Chapter
Tools Chapter
Logout
Tools Chapter
Enable Daylight Savings
Quick Setup
Chapter
Step 1 Time Zone
Step 2 Broadband Type
End Daylight Savings Time
Menu
Description
1.4 PPTP
1.3 PPPoE
1.5 L2TP
1.4 Telstra Big Pond
If your ISP requires a Host Name, type in the host name
This is the IP address that your ISP has given you
THE ROUTER WHEN YOU FINISHED USING THE INTERNET
1.4 PPTP
Password
Click OK when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3
IP Address
1.6 Telstra Big Pond
The IP of the Login Server
Login Server
manually
server manually
General Settings
2.2 WAN
2.1 System
2.3 LAN
2.4 NAT
2.1.1 Time Zone
System Settings
End Daylight Savings Time
2.1.2 Password Settings
2.1.3 Remote Management
Confirmed Password
Host Address
2.2.1 Dynamic IP address
2.2 WAN
2.2.2 Static IP address
2.2.3 PPPoE
2.2.9 DNS
2.2.8 QoS
2.2.10 DDNS
2.2.1 Dynamic IP
Parameter
Gateway
2.2.6 Telstra Big Pond
2.2.7 WAN Policy
The QoS can let you classify Internet application traffic by source/destination IP, MAC address and port number. You can assign priority for each type of application and reserve bandwidth for it. The packets of applications with higher priority will always go first. Lower priority applications will get bandwidth after higher priority applications get enough bandwidth. This can let you have a better experience in using critical real time services like Internet phone, video conference …etc. All the applications not specified by you are classified as rule name “Others”. The rule with smaller priority number has higher priority the rule with larger priority number has lower priority. You can adjust the priority of the rules by moving them up or down
Enable/Disable QoS Add a QoS rule into the table
rule and click “Move Down” to make its priority lower
QoS Rule
The name of this rule
Select the WAN ports that the packets matching
Source Address
Bandwidth
Source MAC Address
Source IP Address
Apply
Reset
Secondary DNS Address optional
Default
Domain Name Server DNS address
Password/Key
Enable/Disable
Provider
DynDNS
LAN IP
2.3 LAN
Lease Time
IP Address Pool
Domain Name
192.168.2.100 to End IP 192.168.2.199 . If you
2.4 NAT
2.4.1 Port Forwarding
“WAN Port” and Comment of the setting to be
The description of this setting
Forwarding setting will be added into the
settings from the Current Port Forwarding
2.4.2 Virtual Server
Public Port
Example Virtual Server
2.4.3 Special Applications
Example
Example Special Applications
UPnP Feature
2.4.4 UPnP
ParametersDescription
2.4.5 Protocol and Port Binding
Add a Rule
2.4.7 Static Routing
2.4.6 ALG Settings
Static Routing function is default disabled. You
Enable Static Routing
have to enable the Static Routing function before
“Default Gateway”, Hop Count and Interface of
rule of Static Routing will be added into the Static
2.5 Firewall
If you want to restrict users from accessing certain Internet applications/servicese.g. Internet websites, email, FTP etc., then this is the place to set that configuration. Access Control allows users to define the traffic type permitted in your LAN. You can control which PC client can have access to these services
Filter client PCs by IP
Add PC
Client PC IP Address
Example Access Control
2.5.2 URL Blocking
2.5.3 DoS Denial of Service
Ping of Death
Intrusion Detection Feature
packets occurred
Discard Ping From WAN
Note DMZ function works only when the NAT function is enabled
Client PC IP Address
3.1 Status and Information Shows the router’s system information
You can see the router’s system information such as the router’s
3.1 Status and Information
Hardware version, Boot code Version, Runtime code Version
the Primary DNS and Secondary DNS being used
3.2 Internet Connection
Server
3.3 Device Status
This page shows the current system log of the Broadband router
3.5 Security Log
updated situation
3.6 Active DHCP Client
This page shows all DHCP clients LAN PCs currently
connected to your network. The “Active DHCP Client Table”
Shows the counters of packets sent and received on WAN and
3.7 Statistics
You can reset the router’s system should any problem exist
4.1 Configuration Tools
This page allows you to upgrade the router’s firmware
4.3 Reset
settings will not be changed. To perform the reset, click on the
some way stops functioning, you can perform a reset. Your
The reset will be complete when the power light stops blinking
Once the reset process is complete you may start using the
Appendix A
How to Manually find your PC’s IP and MAC address
Glossary
Port Number
Application
Telnet
SMTP
