T Imaging problems

 

 

 

 

 

 

 

 

 

 

Problems

Points to check with possible solutions

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1) Display position is incorrect.

Adjust the image position using the “Position” icon

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

in the ScreenManager “Screen” menu. See page 21.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If the problem persists, use the graphics board's

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

utility sofware to change the display position if

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

available. (It may be called “back-porch”.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Change the resolution or refresh rate to match the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

preset mode. See page 11.

 

2) Vertical bars of distortion

Decrease the vertical bars using the“Clock” icon in

 

 

appear.

the ScreenManager “Screen” menu. See page 20.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3)

Letters and lines appear

Adjust the blurred lines using “Smoothing”

 

blurred.

adjustment. Please Refer to the page 23.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4)

Distortion appears like the

This happens when both composite (X-OR) input

 

figure below.

signal and separate vertical synchronizing signal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

are input. Please select either one from the two

 

 

 

 

 

 

 

 

 

 

 

 

 

 

signals.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5)

 

Horizontal bars of distortion

Decrease the horizontal bars using the “Phase”

 

appear.

icon in the ScreenManager “Screen” menu. See

 

 

 

 

 

 

 

 

 

 

 

 

 

 

page 21.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6)

The screen is too bright or

Adjust the contrast and brightness using the

 

too dark.

ScreenManager’s Screen menu. See page 22.

 

 

(The backlight of the LCD monitor has a fixed life

 

 

span. When the screen becomes dark or begins to

 

 

flicker, please contact your dealer.)

 

 

 

7)

After-images appear.

When the screen image has been changed after

 

 

displaying the same image for a long period, after-

 

 

images may appear. Use the Off Timer function

 

 

and avoid leaving the screen on all the time.

 

 

 

8)

Finger prints appears on the

Leaving the screen white may solve the problem.

 

screen.

 

30 3 TROUBLESHOOTING