USA

RATING PLATE

3.1 INSTALLING THE POWER SUPPLY CABLE

To access the power supply cable connection terminal board, proceed as follows:

Model 6 - 10 - 20 GN

Remove the left side panel.

Connect the power supply cable to the terminal board accord- ing to the instructions given in the wiring diagram and fasten the power supply cable by means of strain-relief fitting (not furnished with the oven).

Failure to comply with safety rules and regulations relieves the manufacturer of all liability.

The manufacturer requires when stacking units each appliance have its own branch circuit protection. An air-o-steam® unit stacked with an air-o-chill® unit should have a separate protection for the upper and lower units.

On request the oven is supplied with an optional water softener with automatic regeneration which must be installed on inlet line "B". This device can also be fitted with an optional resin sanitizer kit.

-pressure: 22 to 36 psi (150-250 kPa); higher pressure values result in increased water consumption.

-chlorine ion concentration (Cl -): not more than ~10 ppm (acceptable value) to avoid damaging the oven's internal steel parts.

-pH: over 7.

The oven can be equipped with an optional special filtration unit

which is installed on inlet line "B". This unit also acts as a water softener, reducing water hardness to less than 50ppm (5 °fH)

(optimum value).

-electrical conductivity: 50 to 2000 µS/cm (68°F)(20°C).

Important: The use of water treatment systems featuring technology that differs from that of the systems supplied by the manufacturer is prohibited and will automatically invalidate the

warranty.

The use of dosing systems designed to prevent the build- up of lime-scale in pipes (i.e. polyphosphate dosing systems) is also prohibited since such systems may impair the performance of the appliance.

4. WATER MAINS CONNECTION

(Refer to the installation diagrams at the beginning of this booklet).

This equipment is to be installed to comply with the applicable Federal, State, Local plumbing codes, or the Basic Plumbing Code of the Building Officials and Code Administrators International Inc. (BOCA) and Food Service Sanitation Manual of the Food and Drug Administration (FDA).

When connecting the appliance to the water system with flexible tubes they must be new and not used.

The appliance is fitted with two separate water inlets ("B" and "N"). The water lines supplying both inlets must be fitted with a mechanical filter and shut-off valve (keeping with local plumbing codes).

Before fitting the filters allow the water to flow out for sufficient time to flush any solid particles from the piping.

4.1 WATER SUPPLY CONNECTIONS

4.1.1 WATER INLET "N".

Attention

The water supply pipe (supplied) must have a 3/4" dia (20 mm) pipe and must be without elbow fittings.

The steam condensation system must be connected to a cold quality water supply in keeping with local plumbing codes, with the following characteristics:

-total hardness: total hardness: up to 400ppm (40°fH); in ovens equipped with CLEANING SYSTEM it is advisable to use water of hardness no higher than 50ppm (5°fH).

-pressure: 22 to 36 psi (150-250 kPa); higher pressure values result in increased water consumption.

Note:

To check correct water installation, make sure the rotating wash arm (CLEANING SYSTEM) does not turn below 100 rpm (120 max).

4.1.2WATER INLET "B". (water pipe supplied)

The steam production system must be connected to a quality water supply in keeping with local plumbing codes, with the following characteristics:

- total hardness: 5-50ppm(0.5-5°fH)to reduce the build- up of lime-scale inside the boiler.

4.2 WATER DRAIN SYSTEM

- OVEN level A -

The oven is supplied with an air-break system to prevent any backflow from the drainage system from reaching the oven’s inter- nal circuits and the cooking chamber. The presence of this system means that the drain pipe can be connected directly to the mains drainage system or routed to a floor gulley with grating.

The flexible drainage hose or rigid pipe can be directed to the side or rear of the appliance if the oven is not positioned against a wall; this line must not be directed towards the front of the appliance to prevent interference with roll-in grid racks.The drain- age pipe internal diameter must be no smaller than the oven drain outlet (1 1/4"), no longer than 3 feet (1 metre) and must resist temperatures of up to at least 212°F (100°C). Avoid re- strictions in the case of flexible hose pipes, do not fit elbows on metal pipes anywhere along the drainage line. Also avoid horizontal sections in which water might collect (minimum gra- dient 5%).

WARING: BLOCKING THE DRAIN IS HAZARDOUS.

C - Oven drain

C1 - Safety outlet

Important:

-Do not obstruct the safety outlet C1.

-Do not connect the safety outlet C1 to the drainage system.

Note:

If water comes out of the AIR-BREAK (safety outlet C1) this means the drain C is blocked. Any elimination of the obstruction must be carried out by specialised technical personnel.

5938 035 01

14

Page 14
Image 14
Electrolux 267094 Water Mains Connection, Installing the Power Supply Cable, Water Supply Connections, Water Drain System

260462, 267084, 260450, 269091, 269082 specifications

The Electrolux models 260456, 267085, 269093, 269092, and 269095 represent a series of innovative and high-performing appliances that showcase the brand's commitment to quality, efficiency, and user convenience. Each model is designed with unique features that cater to a range of household needs, making them a popular choice among consumers.

One of the standout features across these models is the incorporation of advanced technology that enhances performance while ensuring energy efficiency. For instance, these appliances often utilize Electrolux’s state-of-the-art Energy Saving technology, which optimizes power consumption, resulting in lower utility bills and a reduced environmental footprint.

The design of each model is sleek and modern, with user-friendly controls that allow for easy operation. Many of these appliances include intuitive touch controls and LED displays, ensuring that users can easily select and adjust settings to suit their preferences. The ergonomic design enhances functionality while also complementing contemporary kitchen aesthetics.

Additionally, the Electrolux 260456, 267085, 269093, 269092, and 269095 models feature multiple cooking modes and settings. They are built to accommodate various culinary techniques, such as baking, grilling, and steaming. This versatility makes them suitable for both novice cooks and seasoned chefs looking to experiment in the kitchen.

Another notable characteristic of these Electrolux appliances is the emphasis on hygiene and cleanliness. Many models come equipped with self-cleaning options, which significantly reduce the effort required to maintain the appliance. The innovative materials used in construction also resist stains and odors, ensuring that the kitchen remains fresh and inviting.

Safety features are paramount in these models, with options like automatic shut-off systems and child safety locks, providing peace of mind for families. The reliability and durability of Electrolux products are also well-known, with many appliances designed to withstand years of use without compromising performance.

Overall, the Electrolux 260456, 267085, 269093, 269092, and 269095 encompass a blend of cutting-edge technology, energy efficiency, and user-centric design. They address the needs of modern consumers while ensuring exceptional performance in the kitchen. Whether for everyday cooking or special occasions, these appliances stand out as reliable partners in culinary endeavors. Electrolux continues to lead the way in promoting innovation and quality in home appliances, and these models are a testament to that legacy.