16 |
|
| Troubleshooting | F4VA1 |
|
|
|
| |
Table 7.4 - Troubleshooting |
|
| ||
|
|
|
| |
Problem | Possible cause | What the user should do |
| |
|
|
|
|
|
The | machine does | No power to machine | Check there is electrical power in the facility |
|
not start |
| Check connection to power lines |
| |
|
|
| Turn on the main power switch |
|
The display is dim | Brightness of the display set too | Increase brightness by pressing button + on the control panel |
| |
|
| low |
|
|
The collar clamp does | The clamp is excluded | Press the COLLAR exclusion button on the control panel to deselect (when the light | ||
not close |
| is off the clamp works) |
| |
|
| Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
|
| sent | filter 3) |
|
The carriage does not | The parameter H06 is set to 03, | Change the setting of the parameter (see table 5.2) |
| |
move |
| 04 or 05 |
|
|
|
| Reflective material is worn out | Replace reflective material strip |
|
|
| The photocell beam does not hit | Check that the photocell has not been moved. If necessary, redirect the photocell | |
|
| the reflective material | beam on the reflective material and lock well the photocell position |
|
The front clamp does | Clamp is excluded | Remove the exclusion by pressing the FRONT button on the control panel (when | ||
not move |
| the light is off the clamp is active) |
| |
|
| Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
|
| sent | filter 3) |
|
The rear clamp does | Clamp is excluded | Remove the exclusion by pressing the REAR button on the control panel (when the | ||
not move |
| light is off the clamp is active) |
| |
|
| Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
|
| sent | filter 3) |
|
|
|
| Check and regulate clamps pressure. Minimum pressure is 3 bar |
|
|
|
| (Figure 4.3, knob 18 and gauge 17) |
|
Both side clamps do | Clamps are excluded (parameter | Set parameter H05 to 01 |
| |
not move | H05 set to 00) |
|
| |
|
| Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
|
| sent | filter 3) |
|
|
|
| Check and regulate clamps pressure. Minimum pressure is 3 bar |
|
|
|
| (Figure 4.3, knob 18 and gauge 17) |
|
Both | side expanders | Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
do not move | sent | filter 3) |
| |
|
|
| Check and regulate clamps pressure. Minimum pressure is 3 bar |
|
|
|
| (Figure 4.3, knob 18 and gauge 17) |
|
Both sleeve arms do | The arms are excluded | Press the ARMS exclusion button on the control panel to deselect (when the light | ||
not move |
| is off the arms work) |
| |
|
| Air pressure is inadequate or ab- | Check and regulate general pressure to 6 bar (Figure 4.3, knob and gauge on | |
|
| sent | filter 3) |
|
No steam from ma- | Steam feed valve closed | Open steam feed valve |
| |
chine |
| Steam time set at zero | Set steam time greater than zero |
|
No blowing | Blowing time set at zero | Set blowing time greater than zero |
| |
Inadequate ventila- | Blowing adjustment set too low | Shift the blowing adjustment lever (12 - Figure 4.3) towards the + mark |
| |
tion |
|
|
|
|