Elektra Beckum Mega 350 D manual Device storage, Available Accessories

26

28 27

•Drain condensate from pressure vessel (29).

29

ACaution!

The condensate contains oil and must be disposed at a proper col- lecting point.

•Check V-belt:

−Remove belt guard (30).

−Retension V-belt or replace, if necessary.

−To adjust the V-belt tension, loosen the four screws at the motor base and shift the motor.

−Tighten the screws at the motor base again.

−Replace the belt guard.

30

AUTO	O
	OFF

Every 250 operating hours

•Replace air intake filter element of compressor pump.

•Replace air filter element of filter/

regulator unit.

Every 500 operating hours

•Drain oil from compressor pump through the drain plug (28) and fill with fresh oil.

ADispose of the waste oil envi- ronmentally safe by taking it to a proper collecting point!

Every 1000 operating hours

•Have unit serviced by an authorized service station. This will extent the compressor's service life considera- bly.

5.2Device storage

1.Switch unit OFF and unplug.

2.Release pressure from tank and all connected air tools.

3.Store device in such way that it can- not be started by unauthorized per- sons.

A Caution!

Do not store device unpro- tected outdoors or in damp environ- ment.

Do not lay device on its side for trans- portation or storing.

6. Available Accessories

For special applications the following accessories are available at your spe- cialist dealer – see back cover for illus- trations:

Sealing

AAir Caulking Gun KP 910

for commercially available car- tridges.

Stock-no. 090 101 0030

Sheet metal cutting

BAir Nibbler BN 540

extra small cutting radius; cuts steel sheet up to 1.0 mm thickness. Stock-no. 090 100 6784

Drilling

CAir Drill BM 310

especially handy tool for low-fatigue working; right-hand rotation only. Stock-no. 090 100 6725

•Air Drill BM 500

(not illustrated) with 3/8" keyless chuck, fully reversible with quick reverse feature.

Stock-no. 090 105 4533

Stapling / nailing

D Combination Air Stapler/Nailer Kombi 40/50

for staples (type 90) from 20 mm to 40 mm and finishing nails (type SKN) from 20 mm to 50.

Stock-no. 090 105 4720mm.

• Combination Air Stapler/Nailer Kombi 40/50

ENGLISH

for staples (type 90) from 15 mm to 32 mm and finishing nails (type SKN) from 16 mm to 32.

Stock-no. 090 105 4711mm.

•Air Stapler KG 80/16

(not illustrated) for staples (type 80) from 6 mm to 16 mm.

Stock-no. 090 105 4681

•Air Stapler KG 90/25

(not illustrated) for staples (type 90) from 15 mm to 25 mm.

Stock-no. 090 105 4690

•Air Stapler KG 90/40

(not illustrated) for staples (type 90) from 20 mm to 40 mm.

Stock-no. 090 105 4703

•Air Finish Nailer SKN 50

(not illustrated) for finishing nails (type SKN) from 20 mm to 50 mm. Stock-no. 090 105 4738

Spray painting

ESpray Gun FB 2200 HVLP high-volume low-pressure feature reduces paint mist bounce-back and provides thicker coating at less paint consumption.

Stock-no. 090 105 4460

•Paint Spray Gun FB 2200

(not illustrated) with 0.5 l flow cup; professional spray gun; steplessly adjustable round, horizontal and vertical spray pattern.

Stock-no. 090 105 4452

•Paint Spray Gun SB 200

(not illustrated) with 1.0 l siphon cup. Stock-no. 090 100 3882

•Paint Spray Gun FB 150

(not illustrated) with 0.5 l flow cup; for spraying primers and paints of varying viskosity.

Stock-no. 090 100 3874

•Paint Spray Gun FB 90

(not illustrated) with 0.75 l flow cup; for spraying primers and paints of varying viskosity.

Stock-no. 090 105 6064

Chiselling

FAir Hammer Set MHS 450

for construction and auto body work Stock-no. 090 100 9210

•Air Hammer Set MHS 315

(not illustrated) to take off plaster and tiles and for light chiselling work.

Stock-no. 090 100 6911

Tyre inflating / checking

GTyre Inflator Gauge RF 480 professional version (calibrated). Stock-no. 090 105 4630

•Tyre Inflator Gauge RF 363

(not illustrated) same as RF 480, but not calibrated.

Stock-no. 090 105 4622

13