Address and Enrollment
Keypads and expander devices that operate on the
The M1KPAS is factory preset to address 16. Valid addresses are 1 to 16. Whenever an M1 control is powered up for the first time only the first keypad (address 1) is automatically enrolled. Any additional keypads must be manually enrolled from “Menu 1 - Bus Module Enrollment”. Before enrolling each device will need to be set with an address.
Setting the Address of an M1KPAS Arming Station:
1.Press and hold the " * " key for 10 seconds. This will place the M1KPAS arming station into setup (bootloader) mode which is indicated by the numeric keys blinking On and Off together. NOTE: Another way to access the setup mode is to remove power by unplugging the data bus cable and applying power while holding any key pressed.
2.Once the unit is in setup mode press the "F" key followed immediately by the "1" key. The unit will now display its current address setting utilizing the Ready (Green), Trouble (Yellow), Armed (Red) LEDs and the EXIT and STAY keys. Each LED or key has an assigned binary value. See table below. The EXIT key (value of 16) will be lighted by itself when the M1KPAS is fresh from the factory.
3.Enter the desired new address number from 1 to 16 and press the EXIT key. OR Press the EXIT key by itself to exit without changing the address.
4.To exit completely from the setup mode press the EXIT key again. The numeric keys will stop blinking On and OFF.
5.The Ready, Trouble, Armed, Exit, and Stay keys will all begin lighting in a clockwise process to indicate that the keypad has not been enrolled with the control. Proceed to the ENROLLING process to make the keypad operational.
| When the M1KAS is in setup mode the LEDs will display the |
|
| |||||
Keypad |
| address setting in Binary Representation |
|
|
| |||
Address | Armed | Trouble | Ready | Stay (Blue) | Exit (Blue) |
|
| |
|
|
| ||||||
| (Red) = 1 | (Yellow) = 2 | (Red) = 4 | = 8 | = 16 | EXAMPLE |
| |
1 | On | - | - | - | - |
| ||
2 | - | On | - | - | - |
| Address 3 | |
3 | On | On | - | - | - | would be | ||
4 | - | - | On | - | - |
| indicated by | |
5 | On | - | On | - | - |
| these 2 LEDs | |
| being ON | |||||||
6 | - | On | On | - | - | Ready Trouble Armed | ||
| ||||||||
|
|
|
|
|
|
| ||
7 | On | On | On | - | - |
|
| |
8 | - | - | - | On | - |
|
| |
9 | On | - | - | On | - |
|
| |
10 | - | On | - | On | - |
|
| |
11 | On | On | - | On | - |
|
| |
12 | - | - | On | On | - |
|
| |
13 | On | - | On | On | - |
|
| |
14 | - | On | On | On | - |
|
| |
15 | On | On | On | On | - |
|
| |
16 | - | - | - | - | On |
|
|
Enrolling the M1KPAS Arming Station: (This step requires an LCD Keypad or the ElkRP software)
1.Press the ELK key, then press 9 (or scroll up) to display 9 - Installation Programming. Press the RIGHT arrow key to select this menu. The Installer Program Code (PIN) must be entered to access this menu.
2.Enter the Installer Program Code. (See M1 Manual for the default Code)
3.The first Installer Programming menu displayed will be "Bus Module Enrollment"
4.Press the RIGHT arrow key to select this menu. "Enrolling Bus Modules" will display
5.The M1 will transmit an enrollment message to all data bus devices, following by a display showing the total Bus Modules that are enrolled. To view the enrolled devices and/or remove a device press the RIGHT arrow key to select Edit mode.
6.Press the * or Exit keys to exit Installer Programming.
Auth.Required Enter Valid Pin
XXBus Modules Enrolled,Editr
Page 3