Manuals / Elo TouchSystems / Computer Equipment / Computer Monitor

Elo TouchSystems ET1X8XC-4XWA-1 manual Connecting Your Touchmonitor, Connect the Video Cable

Models: ET1X8XC-4XWA-1 ET2187C-4XWA-1

1 40

Download 40 pages 45.1 Kb

Page 9

Connecting Your Touchmonitor

Connecting Your Touchmonitor

IMPORTANT: Before connecting the cables to your touchmonitor and PC, be sure that the computer and touchmonitor are turned off.

Female 9-pin serial or	Video cable
USB type touchscreen connector

Female 15-pin

Powervideo

connectorSerial touchscreen cable

OR

USB touchscreen cable

Connect the Video Cable

Connections on underside

Female 15-pin video connector

Video port

Video cable

•Connect one end of the video cable to the video connector on your PC and the other end of the cable to the video connector on your monitor. Secure the cable by turning the thumbscrews on each connector.

2-4E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e

Image 9

Elo TouchSystems ET1X8XC-4XWA-1, ET2187C-4XWA-1 manual Connecting Your Touchmonitor, Connect the Video Cable

Contents

Page For 15, 17, 19 and 21 CRT Open Frame Series Touchmonitors Elo Entuitive Touchmonitor User GuideRevision D ET1X8XC-4XWA-1 Series Models ET2187C-4XWA-1 Series ModelsAppendix A ChapterAppendix B Appendix CCopyright 2003 Elo TouchSystems Inc. All Rights Reserved DisclaimerTrademark Acknowledgments Page INTRODUCTION PrecautionsAbout the Product C H A P T E RPatented iTouch technology from Elo TouchSystems Either RS-232 serial or USB touch interface1-2 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e Unpacking Your Touchmonitor INSTALLATION AND SETUPNOTE Power cord is not included Quick Installation GuideConnect the Video Cable Connecting Your TouchmonitorFemale 9-pin serial or USB type touchscreen connector Connect the Touchscreen Communication CableConnections on underside Serial or USB port2-6 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e Connect the Power CableInstalling the Driver Software 2-8 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e Installing the Touch Driver for MS-DOS and WindowsTo run the INSTALL program Page Using the On Screen Display OSD About Touchmonitor AdjustmentsOPERATION Touchmonitor ControlsFigure 3.1 OSD Menu 3 Push the OSD knob to adjust the highlighted itemEXIT RGB OSDOSD Adjustments Page 9300 6500 ESC OSD OSDPage Problem TROUBLESHOOTINGC H A P T E R Suggestion sPicture is not centered TOUCH TECHNOLOGY Touchscreens An OverviewA P P E N D I iTouch Touchscreens TOUCHMONITOR SAFETY Connector InformationA P P E N D I Should you wish to construct your own custom power cable, Elo highly recommends using AMP Mate-N-Lock part number 350766-1 and male type contacts, AMP part number Touchmonitor Specifications TECHNICAL SPECIFICATIONSPicture Tube Maximum Resolution Deflection Frequency Maximum A P P E N D IPower Management PlugandPlay Compatibility CRT Life Input Signal Input Voltage Display Colors Typical Power ConsumptionOn-Screen Adjustments Safety Regulations EMC IC ES-003 C-Tick VCCI Monitor Dimensions Net Weight Operating Temperature HumidityMechanical OpticalEnvironmental Signal Pinout for CRT Open Frame Monitors SignalPIN Number Power Consumption Recommended primary mode Preset Timing TableREGULATORY INFORMATION Electrical Safety InformationEmissions and Immunity Information DHHS E141667WARRANTY 32 E l o E n t u i t i v e T o u c h m o n i t o r U s e r G u i d e INDEX