Power Requirements, EMC Compliance, Part number | Emerson AMC-S402

Specifications

5.3Power Requirements

The AMC-S402 shall consume no more than the following from the system supplies under normal operating conditions.

Table 9 Power Requirements

Part number	AMC-S402xxx

Management Power	100mA
(MP)

+12V (spin up < 100	1.5A	(18W)
sec)
+12v normal operating	0.9A	(10.8W)

+12v (idle)	0.5A	(6W)

OFF STATE	LESS THAN 0.4W

5.4EMC Compliance

This product was tested in an EMC-compliant chassis and meets the requirements for EN55022 Class A equipment. Compliance was achieved under the following conditions:

∙Conductive chassis rails connected to earth ground, providing the path for connecting shields to earth ground

∙Front panel screws properly tightened

For minimum RF emissions, it is essential that the conditions above be implemented. Failure to do so could compromise the EMC compliance of the equipment containing the module.

6806800H60A AMC-S402 Installation and Use

17

Image 27

Emerson manual Power Requirements, EMC Compliance, Specifications, Part number, AMC-S402xxx

Contents

Installation and Use AMC-S4026806800H60A March Contact Address 2009 Emerson All rights reservedTrademarks Limited and Restricted Rights Legend 2.4.1 Contents2.2.1 2.3.1 IPMI FIRMWARE UPGRADE PROCEDURE 7.2.1SPECIFICATIONS FRONT PANEL INDICATORS List of Tables List of Figures Preface Safety Summary CE Notice European Community Safety StatementFlammability EMI Caution Conventions Used in This Manual commands, options and arguments to commands, andAbout This Manual How This Manual is Organized examples, and system prompts introduce new termscourier System output for example, screen displays and reports Hardware Preparation and Installation Antistatic PrecautionsUnpacking Instructions 1 AMC-S402 Overview 1.1 Features of the AMC Module1.2 PICMG Standards Compliance 1.3 Products Supported by this Manual AMC-S402 Overview 1.4 Part Number, Serial Number Labels Serial Number Final Assembly NumberSub-Assembly Number 5 Safety Label 2.3 Before You Install or Remove the AMC 2 AMC-S402 Installation2.1 Installation and Removal of the AMC-S402 Module 2.2.1 Safety Statement AMC-S402 Installation 2.3.1 Observe ESD Precautions2.3.2 Watch for Bent Pins or Other Damage 2.4 Use Caution When Installing or Removing AMC 2.4.2 Understand Hot Swap 2.5 Verify Slot Usage2.6 Module Hot-Swap 2.7 Installing the AMC Module 2.8 Removing the AMC Module Power Regulator MMC 3 Functional Description3.1 Overview 3.2 AMC-S402, Top Level Board Layout 3.3 Serial Storage I/O Interfaces 3.3.1 SAS Port Isolation Multiplexor CircuitFunctional Description 3.5 IPMI Subsystem 3.4 Power Regulator AMC.3 Serial Storage Port AMC.3 Serial Storage Port 4 Connector Pin Assignments4.2 AMC Connector, “Finger” Assignments 4.1 AMC-S402 Port Assignments Table 6 AMC-S402 Module Edge, Pin Assignments Connector Pin Assignments Pin# 5 Specifications 5.1 Physical Characteristics5.1.1 AMC Module Height Exceptions Specifications 5.2 Hard Drive Operation and Storage Specifications AMC-S402xxx 5.3 Power Requirements5.4 EMC Compliance Part number Table 10 EMC Emission Compliancy Europe Commercial EN 61000-4-4Yes, Class A ITE emissions requirements Australia State 6 Front Panel IndicatorsIndicator Color 7 IPMI Functions List 7.1 IPMI and Management Controller IPMC7.2 Sensor Data Records IPMI Functions List 7.2.1 AMC Port Assignments IPMI Function List 7.3 Supported IPMI Commands AMC Spec DESCRIPTION 8 IPMI Firmware Upgrade Procedure8.1 The ipmitool utility SYNOPSIS IPMI Firmware Upgrade Procedure COMMAND SYNTAX EXAMPLES