Electrical Requirements

Your new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit.

The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds.

WARNING

To reduce the risk of fire, electric shock, or personal injury, mount fan to outlet box marked “Acceptable for Fan Support of 50 lbs. or less”, and use screws supplied with outlet box. Most outlet boxes commonly used for support of light fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.

If your fan is to replace an existing ceiling light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture.

WARNING

Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring. All wiring must be in accordance with National and Local codes and the ceiling fan must be properly grounded as a precaution against possible electrical shock.

Assembly Instructions

CAUTION: The blade assemblies must be mounted on the motor assembly so that the raised lip edge is facing up (Figure 1).

1.Rotate the motor hub so the notched area is above the screw hole in the motor hub. Install one blade assembly on the top of the motor assembly using two M6 x 12mm pan head screws and two M6 lockwashers (supplied) (Figure 1). Repeat this procedure for the remaining two blade assemblies.

2.Remove the two setscrews from the top of the motor coupler (Figure 1). Retain the setscrews for future use.

3.Route the two 80” motor leads through the center hole in the motor cover. Place the motor cover over the motor by aligning the reversing switch hole in the cover over the reversing switch as shown in Figure 2. Secure by installing three M5 x 10mm pan head screws and three M5 external tooth lockwashers (supplied) (Figure 2).

M5 x 10mm PAN HEAD

SCREW (3)

M5 EXTERNAL TOOTH

LOCKWASHER (3)

MOTOR COVER

Figure 2

4.Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod (Figure 3). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in Step 9.

PIN

HANGER

BALL

DOWNROD

SETSCREW

Figure 3

REVERSING SWITCH

M6 x 12mm PAN HEAD SCREW

M6 LOCKWASHER

BLADE

ASSEMBLY

FLAT AREA OF

MOTOR HUB

REMOVE SETSCREW (2)

5. Separate, untwist and unkink the two motor leads,

then route them through the hanger ball/downrod

assembly and seat the downrod in the motor

coupler (Figure 4).

6. Align the clevis pin holes in the downrod with the

holes in the motor coupler. Install the clevis pin and

secure with the hairpin clip (Figure 4). The clevis

pin must go through the holes in the motor coupler

It is critical that the clevis pin in the motor coupler is

properly installed and the setscrews securely

tightened. Failure to verify that the pin and

setscrews are properly installed could result in the

fan falling.

7. Install two setscrews (previously removed in

Step 2) in the motor coupler (Figure 4). While

MOTOR ASSEMBLY

pulling up on the hanger ball, securely tighten both

setscrews.

Figure 1

4

U.L. Model No.: CF765

Page 3 Page 5
Page 4
Image 4
Emerson CF765WW00, CF765BQ00, CF765BS00 owner manual Electrical Requirements, Assembly Instructions
Page 3 Page 5

CF765BS00, CF765WW00, CF765BQ00 specifications

The Emerson CF765 ceiling fans represent a blend of innovative design and cutting-edge technology, making them an attractive choice for modern homes. Available in three stylish finishes—white (CF765WW00), brushed steel (CF765BS00), and black (CF765BQ00)—these fans can seamlessly integrate into various interior designs, from contemporary to classic aesthetics.

One of the standout features of the Emerson CF765 series is its powerful motor. The fan is equipped with a high-performance, energy-efficient motor that ensures optimal airflow while consuming minimal energy. This not only helps to keep energy bills low but also contributes to a more sustainable lifestyle.

These fans come with a reversible motor, allowing homeowners to change the direction of the blades depending on the season. In the summer, the fan can be set to rotate counterclockwise, creating a cool breeze that helps to lower ambient temperatures. In the winter, the reversible function allows the blades to spin clockwise, redistributing warm air trapped near the ceiling down into the living space, enhancing comfort during colder months.

The Emerson CF765 series is designed with user convenience in mind. Each fan includes an easy-to-use remote control that allows users to adjust the fan speed and light settings with just the touch of a button. This feature is especially useful for maintaining comfort without the need for getting up from a seated position.

Additionally, the Emerson CF765 fans feature a sleek and aerodynamic blade design that not only contributes to their modern look but also maximizes air movement efficiency. The blades are made of high-quality materials, ensuring durability and reducing noise levels during operation, making these fans ideal for bedrooms, living rooms, and even home offices.

With a versatile blade span of 52 inches, the CF765 series can effectively cover larger spaces while providing ample airflow. The fans are compatible with a variety of light kits, giving users the option to further enhance their lighting setup, whether they prefer ambient or task lighting.

In summary, the Emerson CF765 ceiling fans—available in white, brushed steel, and black finishes—boast powerful, energy-efficient motors, reversible functionality, and a user-friendly remote control. Their stylish design and efficient cooling capabilities make them an excellent choice for any home, ensuring comfort throughout the year while making a statement in any room's decor.
Top Page Image Contents