Manuals / Emerson / Household Appliance / Home Safety Product

Emerson UVC120, MAN -0016-00 manual Appendix B Procedure For Activating Reed Switches

Models: 0016-00 UVC120 MAN -0016-00

1 45

Download 45 pages 15.97 Kb

Page 40

Appendix B Procedure For Activating Reed Switches

Appendix B Procedure For Activating Reed Switches

W hen activating the MENU/SET and SELECT/RESET reed switches, it is important to orient the magnets provided with the device in the proper direction. They are to be positioned on the faceplate with the curved edge facing the glass. Do not place the flat surface of the magnet against the faceplate. Refer to the diagrams below.

-34-

Image 40

Emerson UVC120, MAN -0016-00 manual Appendix B Procedure For Activating Reed Switches

Contents

ULTRAVIOLET FIRE DETECTION SYSTEM MODEL: U1F, U2F & U4F-UVand UVC1201, 2 and 4 Channel Field Mount Controller with the UVC120 DetectorPage Copyright 2002 Net Safety Monitoring Inc Printed in CanadaPage Table of Contents Unit III SYSTEM INSTALLATIONUnit I GENERAL INFORMATION Unit II UV FIRE DETECTIONUnit IV SYSTEM OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FEATURES CONTROLLER SPECIFICATIONSUnit I GENERAL INFORMATION DESCRIPTIONDETECTOR SPECIFICATIONS <Dimensions: Refer to Figure<Shipping Weight approximate Figure 1 - Controller Dimensions<Temperature Range <Dimensions<Shipping Weight approximate <Detector Enclosure MaterialsBASIC OPERATION - CONTROLLER CONTROLLER FACEPLATE DESCRIPTIONOUTPUTS Relay OutputsRECOMMENDATION Current OutputsAUTOMATIC DIAGNOSTICS AND FAULT IDENTIFICATION EXTERNAL RESETPROGRAMMING OPTIONS Unit II UV FIRE DETECTION VOTING LOGIC not applicable to U1FDETECTOR SYSTEM APPLICATIONGaseous Fuel Handling DETECTOR SENSITIVITY SPECTRAL SENSITIVITY RANGEOther Processes CONE OF VISION SYSTEM SENSITIVITYINSTALLATION GENERAL WIRING REQUIREMENTS Unit III SYSTEM INSTALLATIONCONTROLLER WIRING Page Page Page Page Page Page Page POSITION AND DENSITY OF DETECTORS DIP SWITCH SETTINGSMOUNTING THE DETECTOR CONTROLLER SENSITIVITY ADJUSTMENT CHANNEL SELECTIONU1F, U2F and U4F U2F and U4FFIRE AREA VOTING SEQUENCE not applicable to U1F RELAY OUTPUTS LATCHING/NON-LATCHINGRELAY OUTPUTS ENERGIZED/DE-ENERGIZED Example<SW 5.2: OFF: normally energized operation ON: normally de-energizedoperationTIME DELAY FOR AREA ALARMS RELAY SETTINGSIf switch 5.8 is OFF then in Bypass mode If switch 5.8 is ON then in Bypass modeSTARTUP PROCEDURE CHECKOUT PROCEDUREUnit IV SYSTEM OPERATION MANUAL vi CHECK/COUNT TESTMANUAL CHECK PROCEDURE ALTERNATE TEST PROCEDURE NORMAL OPERATION FIRE RESPONSECurrent Output AUTOMATIC DIAGNOSTICS AND FAULT IDENTIFICATIONSituation MAIN MENU BYPASS MODE bPS SPECIAL FUNCTION MENUFORCED CURRENT OUTPUT MODE FoP ERROR CHECK MODE Err ChcCURRENT CALIBRATION MODE CuC ADDRESS SET MODE Adr Set Do not useUnit V MAINTENANCE ROUTINE MAINTENANCETROUBLESHOOTING DEVICE REPAIR AND RETURNPage APPENDICES Sensitive Device Handling Procedure P u b lis h ed in Accordance with E1A standardAppendix B Procedure For Activating Reed Switches Appendix C Record Of Dip Switch Settings DIP SWITCHAppendix D Common Ultra-VioletAbsorbing Gases Appendix E Wire Resistance In Ohms Page Distributed By 2721 Hopewell Place NE E-mail: netsafe@net-safety.comCalgary, Alberta, Canada T1Y 7J7