5.1Analyzer Module Setup
5.1.18 Inputs and Outputs – Local SIO
Main Menu — Analyzer and
↓
Analyzer module setup
↓[2nd menu page via F5 (More...)]
|
|
|
|
|
| Inputs and outputs |
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ↓ |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ↓ |
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| TAG |
|
|
|
|
|
|
|
|
| 95.00 ppm |
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Analog output setup... |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
| Serial interface setup... |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| Configuration of Relay Outputs... |
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
| Module installed: |
|
|
|
|
|
|
| Enabled |
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Measure |
|
|
|
|
|
|
| Back... |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
| F1 | F2 | F3 | F4 | F5 |
| |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
From the menu "Local SIO Configuration Parameters" you can change to submenus to control and set up several output configurations of the local SIO module.
General Configuration of a SIO board (the whole specification see its own manual):
¨Analog outputs: minimum 2, maximum 8
¨Serial interface (RS 232 or RS 485) to connect the analyzer module with an external computer
¨Three relay outputs
If there is a SIO module installed in the analyzer you have to put in "Enabled" in the line "Module installed", otherwise "Disabled".
Set up parameters:
¨Select the line of variables or any menu line with the ↓
¨Select the variable or change to the submenu with the 8
¨Select the parameter with the −
¨Confirm the new adjustment with the 8
5 - 68 | NGA 2000 |
90003482(2)