5.2 I/O Module Controls 5.2.1 SIO Module – Analog output setup

Analog Output Setup:

Press the 8 -key or the → -key in the line "Analog output setup..." to change to the corresponding submenu:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

 

 

95.00 ppm

 

 

 

 

 

 

 

 

 

 

 

 

 

-- Analog Outputs --

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Output number:

 

 

 

 

1

 

 

 

 

 

 

 

 

 

Choose signal source module...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose signal...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal value for 0% output:

 

 

 

 

0.00 ppm

 

 

 

 

 

 

 

 

 

Signal value for 100% output:

 

 

2500.00 ppm

 

 

 

 

 

 

 

 

 

Output current range:

 

 

 

 

 

0...20 mA

 

 

 

 

 

 

 

 

 

Hold output during calibration?

 

 

 

 

 

No

 

 

 

 

 

 

 

 

 

Signal name:

 

 

 

Concentration

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Current signal value:

 

 

 

 

95.00

 

 

 

 

 

 

 

 

 

Source module:

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

 

 

Back...

 

 

More...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

F3

F4

 

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Configuration of the analog output:

1)Select the analog output number:

·You can set up all parameters in the menu "Analog Outputs" separately for each of the available analog outputs. The number of outputs depends on the hardware configuration of the local SIO module (minimum: 2, maximum: 8).

·Press the 8 -key or the → -key to select the output number and adjust the value you want with the − -key or the ↓ -key.

·Confirm the number selected with the 8 -key.

2)Choose the analyzer module:

·Change with the ↓ -key to the line "Choose signal source module..."

· Change to the submenu "Analyzer Modules" with the 8 -key or the → -key. The tags of all analyzer modules combined with the platform or the MLT analyzer will appear:

MLT25/CH2/R2

 

 

95.00 ppm

 

 

-- Analyzer Modules --

 

 

 

 

 

MLT25/CH1

 

 

 

 

MLT25/CH2

 

 

 

 

MLT25/CH3

 

 

 

 

MLT25/CH4

 

 

 

 

MLT25/CH5

Measure

 

<<<

Back...

>>>

F1

F2

F3

F4

F5

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98

NGA 2000

5 - 85