5.2 I/O Module Controls 5.2.1 SIO Module – Serial interface setup

Serial interface setup:

Press the 8 -key or the → -key in the line "Serial interface setup..." of the menu "SIO - Configuration Parameters" to change to the corresponding submenu:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

95.00 ppm

 

 

 

 

 

 

 

 

 

 

 

 

-- Serial Interface ---

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Baudrate:

 

 

 

 

 

 

19200

 

 

 

 

 

 

 

 

Data bits:

 

 

 

 

 

 

8

 

 

 

 

 

 

 

 

Stop bits:

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Parity:

 

 

 

 

 

 

 

None

 

 

 

 

 

 

 

 

Echo mode:

 

 

 

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

Handshake:

 

 

 

 

 

 

 

Xon/Xoff

 

 

 

 

 

 

 

 

Transmission delay:

 

 

 

 

0

 

 

 

 

 

 

 

 

Type of installed serial interface:

 

 

 

RS232

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Communication protocol:

 

 

 

 

 

 

AK

 

 

 

 

 

 

 

 

Special protocol definitions...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

 

 

Back...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the submenu "Serial Interface" you can determine the parameters of the data transfer between the MLT analyzer or platform and external implements. The set-ups in this menu depend on the configuration of the analyzer resp. platform and the corresponding implement. The specification of the serial interface is described in another manual.

Set up parameters:

¨Select any line of variables or the menu line with the ↓ -key or the − -key.

¨Select the variable or change to the submenu with the 8 -key or the → -key.

¨Select any digit with the ← -key or the → -key and adjust a new value with the − -key or the ↓ -key

resp. select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the 8 -key or

cancel and go back to the last value with the F2 key.

Options:

 

 

 

 

 

 

Baudrate:

300

1200

2400

4800

9600

19200

Data bits:

7

8

 

 

 

 

Stop bits:

1

2

 

 

 

 

Parity:

None

Even

Odd

 

 

 

Echo mode:

Enabled

Disabled

 

 

 

 

Handshake:

None

Xon/Xoff

 

 

 

 

Transmission delay:

0 ... 100

 

 

 

 

 

Type of installed

RS 232

RS 485/2w

RS 485/4w RS 485/4w-Bus

None

 

serial interface:

 

 

 

 

 

 

 

Communication protocol:

AK

MODBUS RTU

None

 

 

Note: Via the line "Special protocol definitions..." you can change to a submenu, where you can set up the parameters of the "AK" or "MODBUS RTU" communication protocol.

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98

NGA 2000

5 - 89