The last five lines of variables in the menu "DIO-Module Outputs" only display some adjustments of the DIO output selected! They are not available:

¨"Module status:" displays the status of the current DIO board.

¨"Slot ID:" displays the tag number of the DIO board selected.

¨"Signal name:" displays the signal selected for the current DIO output.

¨"Signal level:" displays the status of the signal selected.

¨"Signal comes from:" displays the source module selected for the current DIO output.

Configuration of the DIO module inputs:

Press the 8 -key or the → -key in the line "Inputs..." to change to the corresponding submenu:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

95.00 ppm

 

 

 

 

 

 

 

 

 

 

 

 

-- DIO-Module Inputs --

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Inputnumber:

 

 

 

 

 

1

 

 

 

 

 

 

 

 

Choose module...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose function...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Slot ID:

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

Signal name:

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal level:

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

Signal comes from:

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

Next

 

Back...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

F3

 

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "DIO-Module Inputs" you have to determine the configuration for all of the eight DIO module inputs!

DIO input configuration setup:

1)Select the input number:

·Press the 8 -key or the → -key in the line "Inputnumber" and adjust an input number (1, ... , 8) with the − -key or the ↓ -key.

·Confirm the number selected with the 8 -key.

2)Choose the module:

·Change with the ↓ -key to the line "Choose module...".

·Change to the submenu "Analyzer Modules" with the 8 -key or the → -key. (illustration see next page)

All modules joint to the platform or to the MLT analyzer and the control module will be available.

·Go to the line you want with the − -key or the ↓ -key. If there are more than eight source modules available, you have to press the F5 key to go to another menu page.

5 - 94

NGA 2000

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98