5.2 I/O Module Controls

5.2.2 DIO Module(s)

Main Menu — Analyzer and I/O-module expert configuration

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

I/O module controls

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DIO module(s)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

↓

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TAG

 

 

 

 

 

 

 

 

 

 

95.00 ppm

 

 

 

 

 

 

 

 

 

 

 

 

-- DIO-Module Outputs --

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Inputs...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outputnumber:

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

Choose module...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose signal...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Invert output:

 

 

 

 

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

Module status:

 

 

 

 

 

 

 

 

Normal

 

 

 

 

 

 

 

 

Slot ID:

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

Signal name:

 

 

 

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal level:

 

 

 

 

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

Signal comes from:

 

 

 

 

 

 

 

 

????

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Measure

 

 

 

 

Next...

 

 

Back...

 

Ackn!

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

 

F3

F4

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

In the menu "DIO-Module Outputs" you can set up the output configuration of the auxiliary DIO modules. Besides you can change to the submenu "DIO-Module Inputs" to configure the inputs of the auxiliary DIO modules.

Each DIO module is composed of 8 digital inputs and 24 digital outputs. If there exist several DIO modules in the platform, you can change to the setup menu of each with the F3 key. The tag number of the DIO board selected will appear in the line "Slot ID". The changing with the F3 key is not available for MLT analyzers, because only one DIO can be installed in it.

The 24 digital outputs are composed of 3 units with 8 outputs. If there is a short circuit or an overload in one unit, it will be switched off and saved against destruction. After the defect is removed the board is available immediately. You only have to press the F5 key. Informations about the whole specification of the DIO board you will find in another manual.

Set up parameters:

¨Select any line of variables or any menu line with the ↓ -key or the − -key.

¨Select the variable or change to the submenu with the 8 -key or the → -key.

¨Adjust a new value or select the whole parameter with the − -key or the ↓ -key.

¨Confirm the new value with the 8 -key or

cancel and go back to the last value with the F2 key.

Line of variables "Invert output":

Select "Enabled" in the line "Invert output", if you want to invert the measurement signal at the actual digital output, otherwise select "Disabled". The output inversion can be necessary for instance, if you want to combine a failure with an alarm control.

90003482(2) [NGA-e (MLT-Software 3.2.X)] 07/98

NGA 2000

5 - 93