Configuration of Relay Outputs:

Press the ENTER key or the → -key in the line "Configuration of Relay Outputs..." of the menu "LOCAL SIO CONFIGURATION SECTIONS" to change to the corresponding menu:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CLD

 

 

 

 

 

 

95.0 ppm

 

 

 

 

 

 

 

 

 

- CONFIGURATION of RELAY OUTPUTS -

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Outputnumber:

 

 

 

1

 

 

 

 

 

 

 

 

 

Invert signal:

 

 

 

 

Disabled

 

 

 

 

 

 

 

 

 

Choose source module...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Choose signal...

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal comes from:

 

NGA_Control_module

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Signal name:

 

 

 

Function control

 

 

 

 

 

 

 

 

Actual state:

 

 

 

 

 

 

 

Off

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EXPERT

 

 

 

 

 

 

 

INFO

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F1

F2

F3

F4

 

F5

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

There are three relays on any SIO board. With a jumper you can determine the relay contact status: NO (normally opened) or NC (normally closed). Informations about the whole specification of the SIO board you can find in another manual.

In the menu "CONFIGURATION of RELAY OUTPUTS" you have to determine the configuration of the three relay outputs!

Configuration set up:

1) Select the output number:

¨Press the ENTER key or the → -key in the line "Outputnumber" and adjust the output number one, two or three with the − -key or the ↓ -key.

¨Confirm the number selected with the ENTER key.

2) Choose the source module:

¨Change with the ↓ -key to the line "Choose source module...".

¨Change to the submenu "Analyzer Modules" with the ENTER key or the → -key. (illustration see next page)

All analyzer modules joint to the platform or to the MLT analyzer and the control module are available.

¨Go to the line you want with the − -key or the ↓ -key. If there are more than eight source modules available you have to press the F3 key to go to another menu page.

¨Select the tag of the module with the ENTER key or the → -key:

The display will go back to the menu "CONFIGURATION of RELAY OUTPUTS" automatically. The tag of the module selected will appear in the line "Signal comes from".

5 - 36

NGA 2000

90003749(1) [NGA-e (Software CLD 2.3/MLT 3.1.X)] 04/98