WATCHING TV
5Channel Selection
Select channels by using [CH. K / L] or [the Number buttons].
Use [CH. K / L] or [the Number buttons] to select the memorized channels.
or 
or
Using [the Number buttons]
TV
- When selecting analog channel 12
DTV
- When selecting digital channel
•Be sure to press
•Press [CH. RECALL 
] to return to the previously viewed channel.
•When you select a channel larger than 100, press [+100] first. Then use [the Number buttons] to press the lower
•Only [the Number buttons] can be used to select the
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.
What is the minor channel?
By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously. Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.
5Volume Adjustment | INTRODUCTION |
|
This section describes how to adjust the volume.
The mute function, which turns the sound off and on, is also described.
|
|
|
|
|
|
|
|
|
|
|
| |
Use [VOL. X / Y] to adjust the audio volume. | PREPARATION | |||||||||||
or |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
| ||
| VOLUME | 20 |
|
|
| |||||||
|
|
|
| |||||||||
|
|
|
|
|
|
|
|
|
|
| INITIAL | |
|
|
|
|
|
|
|
|
|
|
| ||
• The volume bar will be displayed at the bottom of the | ||||||||||||
| ||||||||||||
TV screen when adjusting the volume. |
|
|
| SETTING | ||||||||
a few seconds. |
|
|
| |||||||||
• The volume bar display will automatically disappear in |
| |||||||||||
Press [MUTE
] to turn off and on the sound.
| MUTE | 20 |
|
| WATCHING TV | |
|
|
|
| |||
|
|
|
|
| ||
• “MUTE” is displayed on the TV screen for a few |
| |||||
OPTIONAL | ||||||
seconds. |
|
|
| |||
Press [MUTE ] again or use [VOL. X / Y] to recover | ||||||
SETTING | ||||||
the original volume. |
|
|
| |||
|
|
|
|
| ||
|
|
|
|
|
| |
|
|
|
|
|
| |
5Switching Each Mode |
|
|
| TROUBLESHOOTING | ||
You can easily switch with the remote control to the DTV (ATSC) and TV | ||||||
(NTSC) or to access external devices when they are connected to the unit. | ||||||
|
|
|
|
| ||
Press [INPUT] repeatedly to cycle through the input | ||||||
| ||||||
modes. |
|
|
|
| ||
|
|
|
| |||
|
|
|
| |||
| ANALOG MODE |
| ||||
NTSC (analog mode) [Air Time] 18:00
| 18:30 |
CH4 | 19:00 |
| 19:30 |
| 20:00 |
| 20:30 |
ATSC (digital mode)
CH4 | No signal | No signal |
| CH4 |
|
(high definition | TV) | |
CH4 | No signal | |
CH4 | No signal | |
CH4 | ||
DIGITAL MODE | INFORMATION | |
VIDEO1 | ||
|
VIDEO2
PC
• To use the video or |
select “VIDEO1”. |
• To use the component video input jacks on the unit, |
select “VIDEO2”. |
major channel | minor channel |
: change automatically
: change manually by using [CH. K/L]
Note:
•“NO SIGNAL” will appear on the TV screen after the minor channel broadcast is over.
• To use the PC input jack on the unit, select “PC”. |
Note:
•When you switch the analog mode to the digital mode, it may take a while until the digital channel selection is completed. “NOW SCANNING“ is displayed while switching the modes.
13
EN
