LIGHTING INSTRUCTIONS

FOR YOUR SAFETY READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a fire or explosion may result

causing property damage, personal injury or loss of life.

 

 

 

the fire

A. This appliance has a pilot which must be lighted by hand.

• If you cannot reach your gas supplier, call

 

When lighting the pilot, follow these instructions exactly.

department.

B. BEFORE LIGHTING smell all around the appliance area

C. Use only your hand to push in or turn the gas control

 

for gas. Be sure to smell next to the floor because some gas

knob. Never use tools. If the knob will not push in or turn

 

is heavier than air and will settle on the floor.

by hand, don’t try to repair it; call a qualified service

 

WHAT TO DO IF YOU SMELL GAS

technician. Force or attempted repair may result in a fire

 

or explosion.

 

• Do not try to light any appliance.

 

• Do not touch any electrical switch;

D. Do not use this appliance if any part has been under water.

 

do not use any phone in your building.

Immediately call a qualified service technician to inspect

 

• Immediately call your gas supplier from a neighbor’s

the appliance and to replace any part of the control system

 

phone, Follow the gas supplier’s instructions.

and any gas control which has been under water.

LIGHTING INSTRUCTIONS

1.STOP! Read the safety information above on this label.

2.Set thermostat to lowest setting.

3.Turn off all electric power to the appliance (if applicable).

4.Remove access panel (front panel).

5.Push in gas control knob slightly and turn clockwise to “OFF.” Do not force.

6.Wait ten (10) minutes to clear out any gas. Then, smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information above on this label. If you do not smell gas, go to the next step.

7.Find pilot - the pilot is attached to front of burner.

8.Turn gas control knob counterclockwise

to “IGN.”

9.Depress and turn gas control knob counterclockwise to “PILOT.” A spark is produced when gas control knob is turned between “IGN” and “PILOT.” Repeatedly depress and turn gas control knob between “IGN” and “PI- LOT” until pilot is ignited. Continue to hold the control knob in for about one (1) minute after pilot is lit. Release knob and it will pop back up. If it goes out, repeat steps 5 through 9.

If knob does not pop up when released, stop and im- mediately call your service technician or gas supplier. •If the pilot will not stay lit after several tries, turn the gas control knob to “OFF” and call your service technician or gas supplier.

10.Attention! Gas control has INTERLOCK latching device. When the pilot is initially lit and the safety magnet is energized (pilot stays on) the INTERLOCK latching device becomes operative. If the gas control is turned to the “OFF” position or gas flow to the appliance is shut off, the pilot cannot be re- lighted until the safety magnet is de-energized (approximately 60 seconds). There will be an audible “click” when the safety magnet in the gas control is de-energized. Pilot can now be relighted. Repeat steps 5 through 9.

11.Turn the gas control knob counterclockwise

to “ON.”

12.Turn on all electric power to the appliance (if applicable).

13.Replace access panel (front panel). Set thermostat to desired setting.

TO TURN OFF GAS APPLIANCE

1.Set the thermostat to lowest setting.

2.Turn off all electric power to the appliance (if applicable), if service is to be performed.

3.Push in gas control knob slightly and turn clockwise to “OFF.” Do not force.

Page 9

12822-4-0806

 

Page 9
Image 9
Empire Comfort Systems RH-65-6 Lighting Instructions, Technician. Force or attempted repair may result in a fire

RH-65-6, RH-65C-1, RH-50-6, RH50C-1 specifications

Empire Comfort Systems has long been a trusted name in the heating solutions market, and their RH series of direct-vent gas heaters exemplifies their commitment to quality and innovation. Among the models in this series, the RH-50-6, RH-65-6, RH-65C-1, and RH-50C-1 stand out for their exceptional performance and user-friendly features.

The RH-50-6 offers a heat output of 50,000 BTUs, making it ideal for smaller spaces needing effective, efficient heating. It features a sleek design and a variety of style options, ensuring it can fit seamlessly into any room. Its direct vent system allows for safe and efficient operation, drawing air from the outside while expelling exhaust gases, thus creating a comfortable indoor environment without compromising indoor air quality.

Similarly, the RH-65-6 model provides a higher output of 65,000 BTUs, suitable for medium to larger areas. This model emphasizes user control with an optional remote control feature, allowing homeowners to adjust the thermostat from the comfort of their couch. The easy-to-use control panel enhances operation simplicity, catering to users of all levels of technical know-how.

The RH-65C-1 and RH-50C-1 models bring additional benefits through their contemporary styling and advanced features. Both units include Empire's exclusive Comfort Control technology. This system optimizes heat distribution throughout the room, ensuring that users experience consistent warmth without hot or cold spots. Alongside aesthetic choices, such as ceramic glass fronts and versatile trim options, these models are designed to provide both functionality and style.

One significant feature across the RH series is the emphasis on energy efficiency. These models meet stringent energy standards, helping homeowners save on utility bills while minimizing environmental impact. The advanced burner technology ensures a clean burn with minimal emissions, aligning with sustainable heating practices.

In conclusion, the Empire Comfort Systems RH-50-6, RH-65-6, RH-65C-1, and RH-50C-1 represent a blend of traditional craftsmanship and modern technology. With various BTU outputs, user-friendly controls, and striking designs, they cater to diverse heating needs, making them outstanding choices for those seeking reliable and efficient home heating solutions.