Energy Speaker Systems e:XL-R, e:XL-15 Connecting the Speaker To AN Amplifier, Care of Finishes

o w n e r s m a n u a l e : X L - S e r i e s

B. Mounting instructions (See Diagram 2):

a. Position the e:XL-28P so the threaded inserts on the bottom are visible.

b. Bolt the stabilizing bars to the inserts with the supplied bolts and ensure that both are securely tightened.

The e:XL28P has a built in 100 watt amplified subwoofer that requires connecting the supplied power cord to the speaker and an AC outlet. Then, the e:XL28P can be connected exactly like a non-powered model, using either conventional speaker wire, bi-wire, or bi-amp/bi-wire configurations.

This model is also equipped with a Level Control & Low Frequency Equalization Control. The variable Level Control will adjust the bass output level. Start with the level in the 12 o'clock position which produces balanced output between the low, mid and high frequencies, and adjust to suit personal taste.

The low frequency equalization allows control of the extreme low frequencies for perfect tailoring to the room's acoustic characteristics. Start at the 12 o'clock position and rotate counter clockwise if the bass is too boomy or unclear, clockwise for more bass impact

The LED located on the front may turn off when bass is absent for extended periods but will automatically turn on when a bass signal returns.

Recommended placement for best imaging, bass response and magnetic shielding (See Diagram1)

CONNECTING THE SPEAKER

TO AN AMPLIFIER

Conventional Connection:

Connect the speaker wire from the positive (RED +) terminal on the amp to the positive (RED+) terminal on the speaker. Connect the negative (BLACK-) terminal on the amplifier to the negative (BLACK-) terminal on the speaker. This method can be applied to bi-wireable speakers as long as the shorting straps are in place on the terminals. (see figure 1,2)

Bi-Wire Connection:

The musical improvements of bi-wiring your speakers can approach those of bi-amping at a substantially lower cost. The standard connection makes the wire common to the low, mid, and high frequency crossover, which is not ideal. Bi-wiring eliminates the common impedance and as a result dramatically cleans up the transition between low and high frequencies. This type of connection is possible on the Energy e:XL-25, e:XL-26 and e:XL-28P. Some companies sell bi-wire cables, but you can also use one cable for low frequencies and one for high frequencies for this purpose. Remove the shorting straps. The tweeter's terminals are on top, the woofer's on the bottom. Twist the positive leads of the two wires together so they can both be inserted into the positive terminal on the amplifier. Follow the same procedure for the negative leads. Then connect the two positive leads to the positive terminals in back of the speaker, and the negative leads to the negative terminals. (see figure 3)

Bi-amp/Bi-wire Combination Connection:

This method uses separate amplifiers for the left and right speakers. Make sure the shorting straps have been removed. Take the negative leads from both the left and right channels of the left amplifier and connect one to the top negative lead, the tweeter, and one to the bottom negative lead, for the woofer. Repeat this process for the positive leads. Follow the same method for connecting the right amplifier to the right speaker. (see figure 4)

ENERGY Powered Subwoofers

Low frequencies are essentially non-directional, so your subwoofer may be placed anywhere in the listening room, without affecting the stereo image of your main speakers. However, placement too near the corner of the room may result in “boomy” bass performance. Positioning the subwoofer further from the corner will normally result in more detailed and accurate performance. For larger rooms, two or more subwoofers may be used. Refer to the connection instructions in the

Owner’s Manual of your Subwoofer.

Amplifier Requirements

ENERGY loudspeakers have been designed to be driven to high listening levels with moderate power, while at the same time being capable of handling the power output of large amplifiers. Most ENERGY speakers have 8 ohm nominal impedance, and will function well with a wide range of amplifiers and receivers.

NOTE: If using more than one pair of speakers per amplifier or receiver, please check with the amplifier manufacturer to confirm that the amplifier can handle loads of 4 ohms.

CARE OF FINISHES

Your speakers should be gently wiped clean with a damp cloth from time to time to remove any dust or stains. Do not use an abrasive cleaner. To remove dust from the grille cloth, use the brush attachment on your vacuum cleaner or a slightly dampened sponge.

WARRANTY OUTSIDE OF THE UNITED STATES AND CANADA

Outside of North America, the warranty may be changed to comply with local regulations. Ask your local ENERGY dealer for details of the LIMITED WARRANTY applicable in your country.

WARRANTY FOR UNITED STATES AND CANADA (see back cover)

“ENERGY”, the “ENERGY” logo, “ Musical Truth”, “e:XL-Series”, the “e:XL Series” logo and “API Accessories” are trademarks of Audio Products International Corp. “Dolby”, “Dolby Pro-Logic” and “Dolby Digital Surround” are trademarks of Dolby Laboratories Licensing. DTS is a Trademark of Digital Theater Systems Inc.

3