•Compressor Delay Active (amber lamp): Under normal operation, when lit, indicates compressor anti-short cycle timer is active. The fan will run but the compressor will be OFF for 6 to 8 minutes.

•Defrost Active (red lamp): When lit, indicates unit is in defrost mode. Defrost mode occurs when ice starts to form on the outside coil. The fan will con- tinue to run but the compressor will stay OFF (not heating) until weather conditions improve.

•Low Pressure (red lamp): When lit, indicates fail- ure in the refrigeration circuit. When this lamp is ON, service is required. Call for service assis- tance.

System Start-Up

1.Verify that the Power lamp is ON and that the pool/spa pump is running and circulating properly.

2.Verify that the control panel Spa-Remote-Poolswitch is in the Remote (OFF) position; see Fig. 4 below.

3.Turn the control switch to either Pool or Spa to turn the system ON and raise the thermostat set- ting above the current water temperature. At this time the 2 green lamps should illuminate. The fan and compressor should start up and run simulta- neously.

4.Allow the heat pump pool heater to operate for a few minutes to stabilize operating pressures and to allow various component temperatures to normal- ize.

5.Verify that the discharge air temperature is approx- imately 8°–10° cooler than the air entering the unit. If not, see the Troubleshooting Section.

Controls (Digital Models)

Your heat pump pool heater incorporates digital safety controls and indicators to ensure its safe, reliable operation (for models with analog controls, see page 10).

Water Pressure Switch: Prevents operation when the pump is OFF. The unit requires 5 psi minimum pres- sure.

Digital Water Temperature Control: The pool water temperature is controlled by the heat pump pool heater’s digital control system, which gives you the option of two settings: one for the desired spa temper- ature and the other for the desired pool temperature. Additionally, as mentioned earlier, the unit is compati- ble with most ‘2-wire’ and ‘3-wire’ control/automation systems.

Fig. 4: Selector Knobs — Analog Models

NOTE: The heat pump pool heater will not run when the Remote position is selected on the Pool/Spa selector switch and there is no remote control sys- tem attached.

Fig. 5: Digital Water Temperature Control

Defrost Sensor: Prevents unit operation if ambient air temperature falls below a predetermined safe mini- mum (approximately 42°–48°F, based on humidity). The compressor will shut OFF but the fan will continue to run.

Delay Timer: Prevents compressor from short cycling, which could damage or destroy the hermetic motor/compressor. Upon water temperature control satisfaction, or other circuit interruptions, this solid state device will prevent compressor restart for approximately 5 minutes.

11

Page 10 Page 12
Page 11
Image 11
Energy Tech Laboratories 5310, 8320, 6310 operating instructions System Start-Up, Controls Digital Models
Page 10 Page 12

5310, 6310, 8320 specifications

Energy Tech Laboratories has made significant strides in the energy sector with its innovative range of products, particularly the models 8320, 5310, and 6310. These energy solutions are designed to meet the increasing demand for efficient, sustainable power generation and management.

The Energy Tech Laboratories 8320 is renowned for its robust performance in renewable energy applications. This model features advanced photovoltaic technology that maximizes energy capture from sunlight, making it ideal for solar power systems. Its integrated smart inverter allows for seamless grid connectivity while ensuring optimal energy conversion. Additionally, the 8320 includes state-of-the-art monitoring capabilities, enabling users to track energy production and consumption in real time. Its compact design and lightweight materials make it suitable for residential rooftops, as well as commercial installations.

Moving on to the 5310 model, this powerhouse focuses on energy storage solutions. Equipped with high-capacity lithium-ion batteries, the 5310 is engineered to store excess energy generated during peak production times for later use. This feature is particularly beneficial for users seeking to maximize their energy efficiency by utilizing stored power during peak demand periods. The 5310 also boasts a user-friendly interface that simplifies the monitoring and management of energy consumption, offering insights that help users make informed energy decisions.

Lastly, the Energy Tech Laboratories 6310 model stands out for its innovative energy management system. This model employs artificial intelligence and machine learning algorithms to optimize energy distribution and usage across various applications. Its decentralized architecture allows for improved energy resilience, making it an excellent choice for large-scale industrial operations and smart grid implementations. With real-time analytics, the 6310 can adapt to changing energy demands, reducing waste and enhancing overall efficiency.

In summary, Energy Tech Laboratories has established itself as a leader in the energy tech sector with its 8320, 5310, and 6310 models. Each product features cutting-edge technologies and characteristics that cater to distinct aspects of energy generation, storage, and management. By harnessing the power of innovation, Energy Tech Laboratories is paving the way for a more sustainable future.
Top Page Image Contents