OPERATION

Prior to starting up or operating the heater, check all fasteners for tightness. In particular, check the set screw in the wheel hub, bearings and the fan sheaves (pulleys). With power and gas to the heater OFF or prior to connecting ventilator to power, turn the fan wheel by hand to be sure it is not striking the inlet or any obstacles. Re-center if necessary.

Start Up

Special Tools Required

•

AC Voltage Meter

•

Amperage Meter

•

Tachometer

•

Manometer

•

Standard Hand Tools

•

Differential Pressure Gauge

Start Up Procedure

1.Check all electrical connections for tightness and continuity.

2.Check pulley alignment and belt tension as described below.

3.Inspect the condition of the intake damper and damper linkage, if provided.

4.Inspect the air-stream for obstructions and install intake filters if missing.

5.Compare the supplied motor voltage with the fan’s nameplate motor voltage. If this does not match, correct the problem.

6.Start the fan up, by turning the external disconnect to the ON position, and shut it OFF immediately to check rotation of the wheel with the directional arrow on the blower scroll. Reversed rotation will result in poor air performance, motor overloading and possible burnout. For units equipped with a single-phase motor check the motor wiring diagram to change rotation. For 3-phase motors, any two power leads can be interchanged to reverse motor direction.

7.When the fan is started up, observe the operation and check for any unusual noises.

Pilot Adjustment

1. Restart the fan and check the gas supply pressure at the inlet

 

gas tap upstream of all electronic valves. The inlet pressure

Pilot Assembly

should be 7 in. - 14 in. w.c. ( 7 in. w.c. – 5 psi on Size 4-5

 

heaters). If the inlet pressure is too high, install an additional

 

pressure regulator external to the unit.

 

2.Open the field installed manual gas shut-off valve and the manual main gas valve on the combination gas control valve.

3.Call for heat with the intake air thermostat (turn set-point to temperature above outside air) and allow the pilot to light. If the pilot does not light, purge the pilot line. If air purging is required, disconnect the pilot line at the outlet of the pilot valve.

4.Check the pilot flame voltage at the Flame Safety Control interface test jacks. A weak pilot flame can be caused by low gas pressure, or a dirty pilot orifice. To adjust the pilot flame, remove the cap from the pilot adjustment screw on the combination gas valve. Increase the pilot gas flow by turning the screw counter-clockwise. Decrease the pilot gas flow by turning the screw clockwise. The pilot DC voltage should read 12 VDC minimum and should typically be 15 VDC.

5.Once the pilot has been established, open the main manual gas shut-off valve downstream of the electronic valves. Check to make sure that the main gas valve opens, and gas flows to the burner.

11

Page 10 Page 12
Page 11
Image 11
Energy Tech Laboratories MR212 manual Operation, Start Up
Page 10 Page 12

MR212 specifications

Energy Tech Laboratories has made significant strides in the field of energy management and efficiency with its groundbreaking product, the MR212. Designed for both industrial and commercial applications, the MR212 stands out for its cutting-edge technology and impressive features that cater to the evolving demands of the energy sector.

One of the main features of the MR212 is its advanced energy monitoring capabilities. Utilizing state-of-the-art sensors and algorithms, the device provides real-time data on energy consumption, helping businesses identify inefficiencies and optimize their energy use. This feature is crucial for organizations aiming to reduce operational costs and minimize their carbon footprint.

The MR212 is equipped with predictive analytics that harnesses machine learning to forecast energy needs based on historical data and usage patterns. This enables users to make informed decisions regarding energy procurement and management, ultimately leading to significant cost savings. Additionally, the system integrates seamlessly with existing infrastructure, making it easy to install and use without requiring a complete overhaul of current operations.

Another notable characteristic of the MR212 is its user-friendly interface. The device features an intuitive dashboard that offers visual representations of energy data, allowing users to monitor performance at a glance. Customizable alerts and notifications help users stay informed of any anomalies or significant changes in energy usage, facilitating prompt action and issue resolution.

The MR212 also supports integration with renewable energy sources, such as solar and wind power. This capability is essential for organizations looking to transition to greener energy alternatives and leverage incentives for using renewable technologies. By integrating seamlessly with these sources, the MR212 not only enhances energy efficiency but also promotes sustainability.

Moreover, Energy Tech Laboratories has ensured that the MR212 is built to withstand industrial environments. With robust construction and compliance with various industry standards, the device is designed for longevity and reliability, providing users with peace of mind.

In conclusion, the Energy Tech Laboratories MR212 is a comprehensive energy management tool that combines advanced monitoring, predictive analytics, and seamless integration with renewable energy sources. Its user-friendly interface and durability make it an ideal choice for businesses seeking to enhance their energy efficiency and sustainability practices. As the demand for smarter energy solutions continues to rise, the MR212 stands at the forefront, paving the way for a more efficient and sustainable future.
Top Page Image Contents