2 weeks after startup

1.Belt tension should be checked after the first 2 weeks of fan operation. Belts tend to stretch and settle into pulleys after an initial start-up sequence. Do not tension belts by changing the setting of the motor pulley, this will change the fan speed and may damage the motor. To re- tension belts, turn the power to the fan motor OFF. Loosen the fasteners that hold the blower scroll plate to the blower. Rotate the motor to the left or right to adjust the belt tension. Belt tension should be adjusted to allow 1/64” of deflection per inch of belt span. Exercise extreme care when adjusting V-belts as not to misalign pulleys. Any misalignment will cause a sharp reduction in belt life and produce squeaky noises. Over-tightening will cause excessive belt and bearing wear as well as noise. Too little tension will cause slippage at startup and uneven wear.

Whenever belts are removed or installed, never force belts over pulleys without loosening motor first to relieve belt tension. When replacing belts, use the same type as supplied by the manufacturer. On units shipped with double groove pulleys, matched belts should always be used.

2.All fasteners should be checked for tightness each time maintenance checks are preformed prior to restarting unit.

Every 3 months

1.Belt tension should be checked quarterly. See instructions in the previous maintenance section. Over-tightening will cause excessive bearing wear and noise. Too little tension will cause slippage at startup and uneven wear.

2.Filters need to be cleaned and/or replaced quarterly, and more often in severe conditions. Washable filters can be washed in warm soapy water. When re-installing filters, be sure to install with the airflow in the correct direction as indicated on the filter.

Filter Quantity Chart

Intake

16” x 20”

20” x 25”

Size 1 Sloped

3

 

Size 2 Sloped

 

3

Size 3 Sloped

6

 

Size 4 Sloped

10

 

Size 5 Sloped

 

8

Size 1 V-Bank

 

3

Size 2 V-Bank

8

 

Size 3 V-Bank

 

8

Size 4 V-Bank

15

 

Size 5 V-Bank

 

12

Yearly

1.Inspect bearings for wear and deterioration. Replace if necessary.

2.Inspect belt wear and replace torn or worn belts.

3.Inspect bolts and set screws for tightness. Tighten as necessary.

4.Inspect motor for cleanliness. Clean exterior surfaces only. Remove dust and grease from the motor housing to ensure proper motor cooling. Remove dirt and grease from the wheel and housing to prevent imbalance and damage.

5.Check for gas leaks and repair if present.

6.Clean flame sensor by rubbing with steel wool to remove any rust build-up,

7.Clean burner with a wire brush and insure burner ports are free of debris. Then wipe the burner with a clean rag.

Burner Orifice

Drill Size

Orifice

Drill Size

Gas Port

31

Air Port

43

26

Page 26
Image 26
Energy Tech Laboratories MR212 manual Weeks after startup, Every 3 months, Yearly, Filter Quantity Chart

MR212 specifications

Energy Tech Laboratories has made significant strides in the field of energy management and efficiency with its groundbreaking product, the MR212. Designed for both industrial and commercial applications, the MR212 stands out for its cutting-edge technology and impressive features that cater to the evolving demands of the energy sector.

One of the main features of the MR212 is its advanced energy monitoring capabilities. Utilizing state-of-the-art sensors and algorithms, the device provides real-time data on energy consumption, helping businesses identify inefficiencies and optimize their energy use. This feature is crucial for organizations aiming to reduce operational costs and minimize their carbon footprint.

The MR212 is equipped with predictive analytics that harnesses machine learning to forecast energy needs based on historical data and usage patterns. This enables users to make informed decisions regarding energy procurement and management, ultimately leading to significant cost savings. Additionally, the system integrates seamlessly with existing infrastructure, making it easy to install and use without requiring a complete overhaul of current operations.

Another notable characteristic of the MR212 is its user-friendly interface. The device features an intuitive dashboard that offers visual representations of energy data, allowing users to monitor performance at a glance. Customizable alerts and notifications help users stay informed of any anomalies or significant changes in energy usage, facilitating prompt action and issue resolution.

The MR212 also supports integration with renewable energy sources, such as solar and wind power. This capability is essential for organizations looking to transition to greener energy alternatives and leverage incentives for using renewable technologies. By integrating seamlessly with these sources, the MR212 not only enhances energy efficiency but also promotes sustainability.

Moreover, Energy Tech Laboratories has ensured that the MR212 is built to withstand industrial environments. With robust construction and compliance with various industry standards, the device is designed for longevity and reliability, providing users with peace of mind.

In conclusion, the Energy Tech Laboratories MR212 is a comprehensive energy management tool that combines advanced monitoring, predictive analytics, and seamless integration with renewable energy sources. Its user-friendly interface and durability make it an ideal choice for businesses seeking to enhance their energy efficiency and sustainability practices. As the demand for smarter energy solutions continues to rise, the MR212 stands at the forefront, paving the way for a more efficient and sustainable future.