Manuals / Enviro / Household Appliance / Stove

Enviro C-11023 owner manual SteelDiagramParts, Evolution Domestic - Steel Components

Models: C-11023

1 36

Download 36 pages 21.74 Kb

Page 34

Image 34

SteelDiagramParts -

��

Evolution Domestic - Steel Components

February 2005

��

		�
			��
				��
				��	�	��
						��
						��
						��
��
�			��
�	�	��
�		��

	��	��
	��	��
		��

Page 34

Image 34

Enviro C-11023 owner manual SteelDiagramParts, Evolution Domestic - Steel Components

Contents

AND USE OF THIS PELLET-BURNING ROOM HEATER. FAILURE TO PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION50-1021 FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTYTable of Contents P.F.I. PELLET STANDARDS IntroductionPellet quality is important, please read the following Store pellets at least 36” 1 m away from the pellet stoveIMPORTANT SAFETY DATA Caution Do not connect to any air distribution duct or systemTHE USE OF CORDWOOD IS PROHIBITED BY LAW SAFETY WARNINGS AND RECOMMENDATIONSKEEP ASH PAN FREE OF RAW FUEL SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCEIntroduction THE REASONS WHY THE UNIT OVERHEATED 7. HEAT OUTPUT INDICATOR Shows the present heat output settingOperating Instructions This may lead to smoke escaping from the stove THERMOSTAT / SWITCH MODE INITIAL START-UP See aboveDO NOT unplug unit while Combustion fan is operating DO NOT OPERATE THE UNIT WITH THE DOOR OR ASH PAN OPEN MANUAL MODEBURNER POT AND LINER 2-3 days Routine Cleaning and MaintenanceTOOLS REQUIRED TO CLEAN UNIT HEAT EXCHANGER TUBES 2-3 daysASH PAN weekly DOOR GLASS CLEANING 2-3 daysOR RAW PELLET FUEL IN ASH PAN FRESH AIR INTAKE biannuallyDOOR GLASS REPLACEMENT POST SEASON CLEAN-UPCLEANING PLATED SURFACES EXHAUST VENT biannuallyInstallation Figure 5 Dimensions of EF5 InstallationAPPLIANCE DIMENSIONS Back Wall Install vent at clearances specified by the vent manufacturerInstallation 3 7.5cmFigure 8 Installing Hearth Pad Pedestal onto EF5 InstallationHEARTH PAD PEDESTAL INSTALLATION NOTE Venting terminals shall not be recessed into walls or siding InstallationEXHAUST InstallationFRESH AIR INTAKE Installation Secure the heater to the floor using the two holes in the pedestalInstallation 2. Install a non-combustible hearth pad where necessaryInstallation A 45 elbow with a rodent screen mayInstallation 2. Place a non-combustible hearth pad where necessaryInstallation Refer to Figures 1. Lock fireplace damper in the open positionthrough vent hole InstallationFigure 23 Through Wall Installation with Exterior Blower Kit InstallationWall Strap To supply power to the exhaust Vent Pipe InstallationRoof Sheathing Rain Cap Roof Flashing Roof Rafters Ceiling Joists Exterior WallREQUIRED, please follow the instructions below If you wish to adjust the slider damper externally NOTInstallation SPECIAL NOTES InstallationDO NOT Troubleshooting2. The stove will not operate when hot WHAT TO DO IF6. The 200 F 93 C high limit temperature sensor has tripped 3. The exhaust motor will not function normally4. Light # 2 on Heat output bar flashing Troubleshooting8. Ignitor- the pellets will not light 9. Control settings Heat Level has no effect on the fire7. The convection blower will not function normally 10. The stove keeps going outWiring Diagram Description Parts ListReference Number Part NumberReference Number Parts ListWire Harness DescriptionEvolution Domestic - Components Parts Diagram - ComponentsFebruary SteelDiagramParts Evolution Domestic - Steel ComponentsINFORMATION ON AN OFFICIAL WARRANTY CLAIM FORM WarrantyWHEN FILING A WARRANTY CLAIM PLEASE COMPLETE THE FOLLOWING TO THE DEALERInstallation Data Sheet 6782 OLDFIELD RD. SAANICHTON, BC, CANADA V8M 2A3