Initial Installation

Leveling legs bracket

Figure 15: Installation of Leveling Legs.

6.Install the leveling legs. Thread the two (2) 5” (13 cm) bolts and locknut up into the captive nuts at each end of the leveling leg bracket (refer to Figure 15).

7.Place the unit part way into the fireplace. Connect the fireplace insert’s flexible gas line to the household gas supply, using locally approved methods. Place the electric cable so it can be connected to the power supply.

8.As you push the unit into its final position in the fireplace, reinstall the vent collar plate to the stove by sliding it along the draft hood and secure with the screw. Adjust the leveling legs to ensure the unit is level.

8.The trim set for your surround panel, must be installed before installing the surround panel onto the unit.

Figure 16: Corner brackets for trim.

Figure 17: Two pieces of corner bracket.

a)Attach one side trim to the top trim using a corner bracket (see Figure 16) to secure pieces together. There are two

(2) main pieces to each corner bracket (see Figure 17). When installing the corner pieces into the trim the “B FACE” sides must face each other and the screw heads are to face out. With the bracket in place and the top and a side trim snug together use a flat head screwdriver to turn the two (2) screws in the bracket in to tighten it into the trim.

b)Slide the two (2) attached trim pieces onto the surround panel.

c)Attach the other side trim piece to the top trim using the same method used in Step a.

d)Place the second side of the trim on the surround panel in the same manner use on the first side and secure in the same manner.

e)On the side trims there are holes 2” (50 mm) from either end. Using a Phillips screwdriver to place a #8 screw 11⁄4” long in each hole and tighten (refer to Figure 18). This will keep the trim tight against the surround.

NOTE: The notch at the bottom of the left trim is so the power cord can be run to the outside of the

panel.Figure 18: Screw to hold the trim against the surround.

14

Page 13 Page 15
Page 14
Image 14
Enviro C-11288 owner manual Installation of Leveling Legs
Page 13 Page 15

C-11288 specifications

Enviro C-11288 is an innovative product that has garnered attention in the environmental technology sector. Primarily designed for sustainability initiatives, this advanced solution integrates a range of features and technologies that address the pressing concerns of waste management and resource conservation.

One of the standout features of Enviro C-11288 is its efficient waste processing capability. Utilizing state-of-the-art waste conversion technologies, it can transform organic and inorganic materials into reusable resources, effectively minimizing landfill use. The incorporation of advanced sorting algorithms ensures that the separation of recyclable materials is efficient and precise, enhancing the overall recycling process.

In addition to waste processing, the Enviro C-11288 is equipped with energy recovery systems. These systems capture and convert waste heat generated during processing into usable energy. This not only energy-optimizes the operation but also contributes to a lower carbon footprint, making it an environmentally friendly solution.

Another significant characteristic of the Enviro C-11288 is its scalability. Whether in a small community or a large industrial setup, the unit can be adapted to meet varying demands. This flexibility is further enhanced by modular design features, allowing users to expand or contract the system as needed without significant interruptions to their operations.

The technology behind Enviro C-11288 is also notable. Real-time monitoring and analytics capabilities enable users to track efficiency metrics, waste reduction rates, and energy consumption. This data-driven approach empowers organizations to make informed decisions about resource management and further improvements.

Durability and low maintenance are additional advantages provided by Enviro C-11288. Constructed with high-quality materials, the system is designed for longevity and can withstand harsh operational conditions. Low maintenance requirements translate into cost savings over time, further appealing to organizations with budget constraints.

Overall, Enviro C-11288 represents a significant advancement in environmental technology solutions. Its combination of waste management efficiency, energy recovery, scalability, real-time monitoring, and durable design positions it as a vital tool for organizations striving to implement sustainable practices while optimizing resource use. As industries continue to emphasize sustainability, the Enviro C-11288 offers a comprehensive solution that aligns with this critical goal.
Top Page Image Contents