Figure 5: Burn pot with liner.

Routine Cleaning and Maintenance

NOTE: Do not use abrasive cleaners to clean the surface or any part of the stove.

The following should be inspected periodically to ensure that the appliance is operating at its optimum and giving you excellent heat value:

2-3 Days / Weekly

Bi-Annually or 2 Tons of Fuel

Burn Pot and Liner

Exhaust Vent

Ash Pan

Fresh air Intake Tube

Inside Firebox

Blower Mechanisms

Door Glass

Heat exchanger tubes

Heat exchanger tubes

Behind firebox liners

Ash pan & Door gaskets

All Hinges

Door Latch

Post Season Clean-up

BURN POT AND LINER (2-3 days)

TOOLS REQUIRED TO CLEAN UNIT

•Torx T-20 Screwdriver

•5/16” Wrench or Socket,

•Brush,

•Soft Cloth

•Vacuum with fine filter bag

The following list of components should be inspected and maintained routinely to ensure that the appliance is operating at its optimum and giving you excellent heat value:

This is the ‘pot’ where the pellets are burned. The burn pot and liner should be inspected every two to three days, to ensure proper air flow through the liner. Failure to keep the liner clean may cause a build up of fuel past the burn pot liner and up the drop tube. This will cause the auger to jam and may result in pellets burning in the drop tube and hopper.

Ensure the unit is cold before cleaning. To remove the burn pot and burn pot liner, open the door using the door handle provided, located on the left-hand side of the stove. Swing the door open. Lift the liner from the burn pot. Lift the burn pot from the firebox by gently lifting the front of the burn pot up first, then sliding the assembly from the air intake tube and the ignitor cartridge. Using a metal scraper, remove material that has accumulated or is clogging the liner’s holes. Then dispose of the scrapped ashes from the liner and from inside the burn pot. Place the burn pot back into the stove, making sure that the pipes are properly inserted into the burn pot and the front tabs are placed in the firebox. Place the liner back into the burn-pot making sure that the ignitor hole in the liner is aligned with the ignitor tube. Push the liner up against the ignitor tube.

●If, after long periods of burning, the fire continually builds up and overflows the burn pot or there is a build up of clinkers, this is an indication that the pellet fuel quality is poor or the stove may need cleaning. Check the stove for ash build up (clean if required) and adjust the slider / damper to produce the proper clean combustion.

Burn pot

 

liner

 

 

Ignitor

 

tube

Fresh air

Burn

tube

pot

 

INSIDE FIREBOX (weekly)

For bi-weekly clean out, ash may be removed from behind the steel plates by rotating the circular cover to allow vacuuming behind the plates.

ASH PAN AND DOOR GASKETS (weekly)

After extended use the gasket may come loose. To repair or replace this, glue the gasket on, using high- temperature fiberglass gasket glue available from your local ENVIRO dealer. This is important to maintain an airtight assembly.

10

Page 9 Page 11
Page 10
Image 10
Enviro EF3 owner manual Routine Cleaning and Maintenance, Burn POT and Liner 2-3 days, Tools Required to Clean Unit
Page 9 Page 11

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.
Top Page Image Contents