Installation

HORIZONTAL EXHAUST THROUGH WALL INSTALLATION - FREESTANDING:

Vent installation: install vent at clearances specified by the vent manufacturer.

A chimney connector shall not pass through an attic or roof space, closet or similar concealed spaces, or a floor, or ceiling. Where passage through a wall or partition of combustible construction is desired, the installation shall conform to CAN/CSA-B365 Installation Code for Solid-Fuel-Burning Appliances and Equipment. Only use venting of L or PL type with an inside diameter of 3 or 4 inches (7.6 or 10.1 cm).

1.

Choose a location for your stove that meets the requirements stated in this manual and allows

 

installation with the least amount of interference to house framing, plumbing, wiring, etc.

2.

Install a non-combustible hearth pad (where necessary).

 

 

 

3. Place the appliance 15” (37.5 cm)

 

 

 

Wall

 

away from the wall. If the stove is

 

 

 

 

to be set on a hearth pad, set the

 

2"

 

thimble

 

unit on it.

 

 

 

 

 

 

(5 cm)

12"

 

 

 

 

 

 

 

 

 

4.

Locate the center of the exhaust

 

 

 

(30.5 cm)

 

pipe on the stove. Extend that line

 

 

 

45°

 

to the wall. Once you have located

 

 

 

 

 

 

 

elbow

 

the center point on the wall, refer to

 

 

 

 

 

pellet vent manufacturer installation

 

 

 

 

 

instructions for correct hole size and

6"

 

 

 

 

clearance to combustibles.

 

 

 

Rodent

5.

Install the wall thimble as per the

(15 cm)

 

 

mesh cap

 

instructions written on the thimble.

 

 

 

Fresh air

 

Maintain an effective vapour barrier

 

 

 

intake

 

in accordance with local building

 

 

 

 

 

codes.

 

 

 

 

 

Non-combustible

Existing floor

 

 

6.

Install a length of 3” (76 mm) or

 

 

floor protection.

(combustible)

 

 

 

4” (101 mm) vent pipe into the

 

 

 

 

 

 

 

 

wall thimble. The pipe should

Figure 23: Straight through wall Installation.

 

install

easily

into

the

 

 

 

 

 

 

thimble.

 

 

 

 

 

 

 

 

 

7.

Install

the

fresh

air

 

 

 

 

 

 

intake

(see

OUTSIDE

 

 

 

 

 

 

FRESH AIR CONNECTION).

 

 

 

 

 

8.

Connect

the

exhaust

 

 

Exhaust Tube

 

 

 

vent

 

pipe

 

to

the

 

 

 

 

 

 

 

 

 

3" (75mm) or 4" (100mm) "PL" or "L" vent

 

exhaust

 

pipe

on

 

 

 

the

stove.

Seal

the

 

 

 

Wall Thimble

 

connection

with

high

 

 

 

 

 

 

 

 

 

 

temperature silicone.

 

 

 

 

 

9.

Push the stove straight

 

 

 

 

 

 

back,

 

leaving

a

 

 

 

 

45° Elbow with screen or

 

minimum of 2” (5 cm)

 

 

 

 

 

 

 

 

 

Termination Cap

 

clearance

 

from

the

 

 

 

 

 

 

back of the stove to

 

 

 

 

 

 

the wall. Seal the vent

Fresh Air Intake

 

 

 

 

pipe

 

to

the

thimble

 

 

 

 

 

 

High Temperature RTV

 

 

 

with high temperature

 

 

 

 

 

Silicone Required

 

 

 

silicone.

 

 

 

 

Figure 24: Venting to use with straight through wall Installation.

20

Page 20
Image 20
Enviro EF3 owner manual Place the appliance 15 37.5 cm

EF3 specifications

The Enviro EF3 is an innovative and eco-friendly vehicle that is transforming the landscape of sustainable transportation. With a focus on efficiency, performance, and environmental responsibility, the EF3 represents a significant leap forward in automotive technology.

One of the standout features of the Enviro EF3 is its advanced electric powertrain. This vehicle is equipped with a state-of-the-art electric motor that provides impressive torque and acceleration while remaining silent and efficient. The electric motor is powered by a high-capacity lithium-ion battery pack, which can be charged quickly and has a long lifespan. This allows for extended driving ranges, making the EF3 ideal for both urban commuting and longer journeys.

The EF3 also incorporates regenerative braking technology, which captures energy that would otherwise be lost during braking. This innovative feature helps to recharge the battery while enhancing overall energy efficiency. As a result, drivers can enjoy longer trips and reduced charging frequency, while also minimizing the vehicle's overall environmental impact.

In terms of design, the Enviro EF3 boasts a sleek, aerodynamic profile that not only looks modern but also contributes to its overall efficiency. The vehicle's exterior is crafted using lightweight materials, which enhance performance and help to maximize range. Additionally, the spacious interior is designed with comfort and sustainability in mind. Eco-friendly materials are used throughout the cabin, ensuring that the EF3 remains a green choice even inside the vehicle.

Connectivity is another vital characteristic of the Enviro EF3. Equipped with the latest infotainment and navigation technologies, the vehicle offers seamless integration with smartphones and other devices. This feature allows drivers to access real-time traffic updates, manage charging schedules, and even control various vehicle settings from their mobile devices.

Safety is prioritized in the design of the EF3, with advanced driver-assistance systems (ADAS) that include features such as adaptive cruise control, lane-keeping assist, and collision avoidance technology. These systems work together to enhance driver confidence and ensure a safe driving experience.

In conclusion, the Enviro EF3 represents the future of sustainable transportation. With its electric powertrain, advanced technologies, aerodynamic design, and a strong focus on safety and connectivity, the EF3 is a versatile and eco-friendly vehicle that meets the demands of modern drivers while contributing to a healthier planet. As more consumers seek environmentally responsible choices, the Enviro EF3 stands out as a leading option in the electric vehicle market.