Epson Equity II Index

Index

Access slot cover 41-43 Access slots, option card 9-10 AC input 9-10, 21, 45

AC outlets switched 9, 12 unswitched 9, 12, 16

Adjusting keyboard legs 14 Alt 24-27

Application program 24, 44, B-1ARCHIVE 35

Arranging components 5 horizontal main unit 5 vertical main unit 6

ASCII 16, B-1Asynchronous A-2,B-1Auxiliary power outlets 4

Back panel 8-10, 38, 41 Back panel screws 38

Background color, monochrome monitor 25 Backup 22, 33, 35, 46, B-1

Backspace key 25 Battery 49-50, A-1Bit A-1,B-1Boot 22, B-1

Brightness control, monitor 22, 46 Button, PUSH 7-8, 24, 30 Built-in interface

parallel 1, 14 serial 1, 16 video 1, 11

Button, reset 7-8, 26-27 Byte 30, A-1,B-1

Cable

keyboard 7-8, 12-14 monitor 11-12, 46 power 9-10, 21, 45 printer 15-16

Caps Lock 24-25 Card

option See Option card registration 3

Centronics-compatible 14 Character 16, 25, B-l

Index-l

Contents

Equity™ User’s Guide Page Page Equity II User’s Guide (Page 18) G W-BASICfor the Equity II/III (Pages 7-203to 7-207) MS-DOSfor the Equity II/III (Page 10-16) Contents Appendixes Figures Tables Introduction How To Use This Manual Setting Up Your System Unpacking Choosing a Location Choose a location that provides the following: Arranging the Components Figure 1-2.Alternate system arrangement The Front Panel The Back Panel Figure 1-4.Back panel The back panel components work as follows: Connecting the Power Cord Connecting a Video Monitor Connecting the Keyboard Figure 1-7.Connecting the keyboard Connecting a Printer Figure 1-9.Printer placement Figure 1-10.Connecting a printer 5.Plug the printer’s power cable into an electrical outlet Serial interface The Equity II character set Setting the DIP Switches Table 1-1.Set 1 DIP switches Switch (internal parallel Table l-2 and the descriptions below explain how to set the DIP switches in set l-2 Note: Switches 2-l through 2-4 and switch 2-6 are not used. Leave them Table 1-2.Set 2 DIP switches 8 (internal serial Using the Equity 64g KB RAM available Inserting and Removing Diskettes Special Keys on the Equity II Keyboard Using MS-DOSon the Equity Selecting an Execution Speed Resetting the Computer Turning Off the Equity Using Disks and Disk Drives How Disks Work Choosing Diskettes for the Equity Table 3-lshows what types of diskettes to use in the two types of drives Table 3-1. Drive/diskette compatibility Caring for Disks and Disk Drives Protecting your Data Using a Single Floppy Disk Drive Using a Hard Disk Drive Page Installing Option Cards Removing the Main Unit Cover As shown in Figure Figure 4-1. Back panel screws Figure 4-2.Side screws under plastic inserts Figure 4-3.Removing the main unit cover Installing an Option Card Figure 4-d. Inserting an option card 7.Keep the card’s packing materials in case you need to remove the card later Removing an access slot cover Replacing the Main Unit Cover Post-InstallationAdjustments Removing an Option Card Using a Mouse Using a Modem Troubleshooting The Computer Fails To Start Up The Video Display Does Not Appear The Computer Hangs Up or Freezes Floppy Disk Problems Hard Disk Problems Software Problems Printer Problems Option Card Problems Memory Problems The Battery Is Low CMOS battery needs replacing Page Equity II Specifications CPU and Memory Controllers Interfaces Power Supply Mass Storage Keyboard Environmental Requirements (5"to35T) Physical Characteristics (CPU Only) Power Requirements Options Glossary Code Command Configuration Control code CPU Disk drive has a Diskette DOS Double-density Hardware Any physical Highdensity data Input/output port Monochrome monitor Mouse MS-DOS An operating system from Microsoft. See DOS, Operating system Operating system Program Read Read/write head Reset RGB Software The programs that System diskette Write-protect tab Index Page Page Page Page Page Page Page Page 22 B-6 16 RS-232Cport 9-10, 16, A-2, B-6 secondary B-7 10-11 21, 27 12 A-4