EPSON
Default Settings
While you can often set the default settings through your application software or printer driver, you may need to change a default setting from the printer’s control panel using the default setting mode. The table below lists the default settings (in bold) and options you can select in this mode.
Settings | Options |
|
|
Page length for tractor | Length in inches: 3, 3.5, 4, 5.5, 6, 7, 8, |
| 8.5, 11, 70/6, 12, 14, 17 |
|
|
Skip over perforation | On, Off |
|
|
Auto | On, Off |
|
|
Auto line feed | On, Off |
|
|
Print direction | |
|
|
Software | ESC/P, IBM 2380 Plus |
|
|
0 slash | On, Off |
|
|
High speed draft | On, Off |
|
|
I/F mode | Auto, Parallel, Serial |
|
|
Auto I/F wait time | 10 seconds, 30 seconds |
|
|
Baud rate (bps) | 19200, 9600, 4800, 2400, 1200, 600, |
| 300 |
|
|
Parity | None, Odd, Even, Ignore |
|
|
Parallel I/F bidirectional mode | On, Off |
|
|
Packet mode | Auto, Off |
|
|
Character table* | Standard model: |
| Italic, PC 437, PC 850, PC 860, |
| PC 863, PC 865, PC 861, BRASCII, |
| Abicomp, Roman 8, ISO Latin 1, |
| PC 858, ISO |
| All other models: Italic, PC 437, |
| PC 850, PC 437 Greek, PC 853, |
| PC 855, PC 852, PC 857, PC 866, |
| PC 869, MAZOWIA, |
| Code MJK, ISO |
| Bulgaria, PC 774, Estonia, |
| ISO |
| PC APTEC, PC 708, PC 720, |
| PC AR864, PC 860, PC 863, PC 865, |
| PC 861, BRASCII, Abicomp, |
| Roman 8, ISO Latin 1, PC 858, |
| ISO |
|
|
International character set for | Italic U.S.A., Italic France, Italic |
Italic table | Germany, Italic U.K., Italic Denmark1, |
| Italic Sweden, Italic Italy, Italic Spain1 |
|
|
Manual feed wait time | 1 second, 1.5 seconds, |
| 2 seconds, 3 seconds |
|
|
Buzzer | On, Off |
|
|
Auto CR (IBM 2380 Plus)* | On, Off |
|
|
IBM character table* | Table 2, Table 1 |
|
|
*These settings take effect only when IBM 2380 Plus emulation is selected.
Changing Default Settings
Follow the steps below to enter the default setting mode and change the printer’s default settings.
To print the language selection and default setting mode instructions, you need 5 sheets of letter- or
1. Make sure paper is loaded and the printer is turned off.
Whenever you turn off the printer, wait at least 5 seconds before turning it back on; otherwise you may damage the printer.
2.While holding down the Tear Off button, turn on the printer. The printer enters the default setting mode and prints the language selection instructions.
3.If you need to select a different language, press the LF/FF button until the Tear Off lights indicate the language you want, as described in the language selection instructions.
4.Press the Tear Off button to confirm your language selection and print the current default settings.
5.If you do not need to change any settings, go to step 6.
If you want to change any of the default settings, press the Tear Off button to print the instructions (three pages) in the language you selected.
Follow the instructions to change the default settings using the buttons on the printer’s control panel.
The arrows on the instruction sheets indicate the printer’s current settings.
6.When you finish, turn off the printer to exit the default setting mode. The current settings remain in effect until you change them again.
5/00 | EPSON |