Manuals / Brands / Home Audio / Stereo Receiver / Ericsson / Home Audio / Stereo Receiver

Ericsson RX8200 Installing the Equipment, 2.1Introduction, 2.2Operating Voltage, 2.3Power Cable and Earthing, Note:, AC Models

1 44

Download 44 pages, 1.71 Mb

Installing the Equipment

2	Installing the Equipment

2.1Introduction

For best performance and reliability follow the instructions for site requirements and installation in the Reference Guide and only use installation accessories recommended by the manufacturers.

Warning!

Do not remove the covers of this equipment. Hazardous voltages are present within this equipment and may be exposed if the covers are removed. Only Ericsson trained and approved service engineers are permitted to service this equipment.

2.2Operating Voltage

Caution!

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your business, consult a qualified electrical engineer or your local power company.

Note: Refer to the Reference Guide for details of the color codes used on the mains leads.

See Table 5 for fuse information and also the Reference Guide for a full power supply specification.

AC Models

AC models are fitted with a wide-ranging power supply. It is suitable for supply voltages of 100-240 V AC -10% +6% at 50/60 Hz nominal.

2.3Power Cable and Earthing

Check that the power cable is suitable for the country in which the Receiver is to be used.

EN/LZT 790 0009 R1A 2011-03-30

9 (44)

Contents

RX8200 Advanced Modular Receiver Copyright Disclaimer Customer Services Europe, Middle East and Africa Contents Quick Start Guide: Connect-Power-Configure List of Figures List of Tables 1 Introduction 1.1Who Should Use this User Guide 1.2What Equipment is Covered by this User Guide 1.3Hardware and Software Options Page Page Page Installing the Equipment 2.1Introduction 2.2Operating Voltage 2.3Power Cable and Earthing 2.4Rear Panel Connectors 2.5Connecting the Receiver to the Power Supply Quick Start Guide: Connect-Power-Configure 3.1Connecting the Receiver 3.2Powering the Receiver 3.2.1Switching On 3.2.2Power Up Operating Modes 3.3Configuring the Inputs 3.3.1Transport Stream (ASI) Input 3.3.2Satellite (DVB-Sor DVB-S2)Input (if fitted) 3.3.3IP (GIGE) Input (if fitted) 3.3.4G.703 (ATM) Input (if fitted) 3.4Selecting a Decode Service (Program) 3.5Configuring the Video Output 3.6Configuring the Audio Outputs 3.7Configuring for Single-serviceDecryption 3.8Configuring for Multi-serviceDecryption Front Panel Control 4.1Introduction 4.2Receiver Front Panel 4.3Using the Front Panel Controls 4.3.1Status LED 4.3.2LCD 4.3.3Arrow Pushbuttons 4.3.4Edit and Save Pushbuttons 4.4Front Panel Menus Page 4.4.1Menu Structure Director Output Menu Output Selection TS Feed Selection Presets 5 Web Browser Control 5.1Introduction 5.1.1Setting Up Web Browser Remote Control 5.2Using the Web Browser Interface 5.2.1Navigation Header About Function Tabs 5.2.2Viewing the Web Pages 5.3Web Pages 5.3.1Status 5.3.2Device Info Environment Network Settings Modules Trap Destination Table 5.3.3Alarms 5.3.4Customization Web Page 5.3.5CA 5.3.6Input Satellite Input RF Selection Configuration IP Input Page 5.3.7Service Plus 5.3.8Decode VBI-VANC Splice DVB Subtitles Teletext 5.3.9Output 5.3.10Download 5.3.11SNMP 5.3.12Presets 5.3.13Save/Load 5.3.14Help 6 Equipment Packaging 6.1Packaging Statement 6.2Packaging Markings Materials Declarations 7.1Overview 7.2For the European Union 7.3For China Disposal of this Equipment 8.1General 8.2For the European Union 9 Recycling