Contents | Exmark E-Series guide

Contents
Introduction	3
Safety	5
Safety Alert Symbol	5
Safe Operating Practices	5
Safety and Instructional Decals	11
Specifications	15
Model Numbers	15
Systems	15
Dimensions	16
Torque Requirements	17
Product Overview	18
Operation	18
Controls	18
Pre-Start	21
Operating Instructions	21
Transporting	25
Maintenance	27
Recommended Maintenance Schedule(s)	27
Periodic Maintenance	28
Check Engine Oil Level	28
Check Battery Charge	28
Check Mower Blades	29
Check Safety Interlock System	30
Check Rollover Protections Systems (Roll
Bar) Knobs	31
Check Seat Belt	31
Check for Loose Hardware	31
Service Air Cleaner	31
Change Engine Oil	31
Check Hydraulic Oil Level	31
Check Tire Pressures	32
Check Condition Of Belts	32
Lubricate Grease Fittings	32
Check Spark Plugs	32
Replace Emissions Air Intake Filter	32
Change Hydraulic System Filter and
Fluid	33
Check Spark Arrester (if equipped)	34
Thread Locking Adhesives	34
Copper-BasedAnti-seize	34
Dielectric Grease	34
Adjustments	35
Deck Leveling	35
Adjusting the Blade Slope	35
Pump Drive Belt Tension	36
Deck Belt Tension	36
Adjusting the Parking Brake	36
Motion Control Handle Adjustment	37
Full Forward Tracking Adjustment	37

Motion Control Linkage Adjustment	38
Adjusting the Seat Ride Suspension	39
Electric Clutch Adjustment	39
Cleaning	40
Clean Engine and Exhaust System
Area	40
Remove Engine Shrouds and Clean Cooling
Fins	40
Clean Hydro Fan Cooling Fins	40
Clean Debris From Machine	40
Clean Grass Build-Up Under Deck	40
Waste Disposal	40
Troubleshooting	42
Schematics	44

4

Image 4

Exmark E-Series manual Contents

Contents

Pioneer E-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices Training Safety Operation Slope Operation Using the Rollover Protection System Rops Maintenance and Storage Safety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Model Numbers SpecificationsSystems Dimensions Hydrostatic Ground Drive SystemTires & Wheels Cutting Deck Torque Requirements Product Overview Operation ControlsMotion Control Levers Choke Control Ignition Switch Fuel Shut-Off Valve Throttle ControlBrake Lever Hour Meter PTO Engagement Switch Drive Wheel Release Valves Pre-Start Operating InstructionsDeck Lift Pedal Transport Lock Starting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Cutting Height Adjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Operation Maintenance Recommended Maintenance Schedules Recommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Do Not jump start a weak battery if these conditions exist Check Mower Blades Check Safety Interlock System Service Dealer Service Air Cleaner Check Rollover Protections Systems Roll Bar KnobsCheck Seat Belt Check for Loose Hardware Check Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Check Spark Plugs Service Interval After the first 100 hours Change Hydraulic System Filter and Fluid Check Spark Arrester if equipped Thread Locking AdhesivesCopper-Based Anti-seize Dielectric Grease Adjusting the Blade Slope Deck Leveling Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Motion Control Handle Adjustment Full Forward Tracking Adjustment Motion Control Linkage Adjustment Adjusting the Seat Ride Suspension Electric Clutch Adjustment Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From Machine Battery Disposal Troubleshooting Problem Possible Cause Corrective Action See Drive Wheel Release Valves section Schematics Electrical Diagram Electrical Logic Schematic Pioneer E-Series Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options