Manuals / Exmark / Lawn and Garden / Lawn Mower

Exmark Lazer Z T H I S I S A 5 S L O P E, T H I S I S A 1 0 S L O P E, T H I S I S A 1 5 OSL P E

Models: Lazer Z

1 44

Download 44 pages 4.59 Kb

Page 43

Image 43

ALIGN THIS EDGE WITH A VERTICAL SURFACE (TREE, BUILDING, FENCE POST, POLE ETC.)

T H I S I S A 5 ° S L O P E

EXAMPLE: COMPARE

SLOPE WITH FOLDED

EDGE.

T H I S I S A 1 0 ° S L O P E

T H I S I S A 1 5 ° OSL P E

HT I S I S A 2 0 ° EPOLS

FOLD ALONG APPROPRIATE LINE

- 38 -

Page 43

Image 43

Exmark Lazer Z manual T H I S I S A 5 S L O P E, T H I S I S A 1 0 S L O P E, T H I S I S A 1 5 OSL P E

Contents

Page HEALTH WARNING GASOLINE W A R N IN GFAILURE TO FOLLOW CAUTIOUS OPERATING PRACTICES CAN RESULT IN SERIOUS OPERATOR INJURYEFFECTIVE DATE September 1 Program EXMARK PARTS PLUS PROGRAMHow the Program Works OPERATORS MANUAL 5. MAINTENANCE & ADJUSTMENTS 1. SAFETY2. SPECIFICATIONS 3. ASSEMBLY INSTRUCTIONS1.2 TRAINING 1. SAFETYATTENTION! BECOME ALERT YOUR SAFETY IS INVOLVED 1.1 SAFETY ALERT SYMBOL1.4 OPERATION 1.4.9 Start the engine carefully with feet well away from the blades 1.7 SAFETY SIGNS 1.5 MAINTENANCE AND STORAGE1.6 RIDING ATTACHMENTS LOCATION Front Corners of Deck LOCATION ConsoleLOCATION Right Rear Corner of Deck LOCATION Upper Handles PART NO. 403005Both Sides2.3 FUEL SYSTEM 2. SPECIFICATIONS2.1 MODEL NUMBER 2.2 ENGINE2.7 WHEEL DRIVE SYSTEM 2.4 SAFETY INTERLOCK SYSTEM2.5 STEERING/BRAKE CONTROL 2.6 TRANSMISSION2.10 DIMENSIONS 3. ASSEMBLY INSTRUCTIONS2.11 TORQUE REQUIREMENTS UPPER HANDLE MOUNTING Do not over tightenKOHLER SPEED CONTROL THROTTLE CABLE HOOK-UP UPPER HANDLE HEIGHT ADJUSTMENTB&S 10.5 hp SPEED CONTROL THROTTLE CABLE HOOK-UP KAWASAKI SPEED CONTROL THROTTLE CABLE HOOK-UPFor B&S 8.5 hp Engines 3.8.5 Install and adjust wheel drive linkages LEVER AND ROD ADJUSTMENTTHIS CLEARANCE SHOULD BE EQUAL SHIFTER LEVER TO TRANSMISSIONClevis Pin NEUTRAL LOCK LEVER CLEARANCEDrive Lever Hardware Location 3/16” TO 1/4” Neutral Lock Park Brake Latch Drive Linkage5.1.12 for locations and grease amounts 4. OPERATION INSTRUCTIONS4.1 CONTROLS NOTE UNIT IS NOT GREASED AT THE FACTORY! Refer to SectionKawasaki,Kohler, and B&S 10.5 hp Engines DRIVE LEVER, NEUTRAL LOCK/PARK BRAKE LATCH OPERATIONB&S 8.5 hp Engines 4.2 PRE-START4.3 OPERATING INSTRUCTIONS NOTE Kawasaki engines generally need to be choked even when warm4.3.4 Drive Lever/Neutral Lock/Park Brake Latch Operation Do not rely solely on the parking brake to hold machine on trailer 5. MAINTENANCE AND ADJUSTMENTS5.1 PERIODIC MAINTENANCE 4.4 TRANSPORTINGService Interval Daily Service Interval DailyBLADE BOLT INSTALLATION 5.1.2 Clean engine air cooling systemService Interval Daily If the mower engine does not stop under any of theService Interval Daily Do Not overfill Service Interval 40 hrsNote Front caster tires have permanent tire sealant installed Service Interval 160 hrsNOTE A Secondary blade drive belt is used on 48 units LUBRICATION CHARTService Interval Refer to Chart SERVICEPIVOT POINTS SPRAY LUBRICANT CHARTSERVICE INTERVAL Service Interval As Required5.2 ADJUSTMENTS AXLE HEIGHT ADJUSTMENT CASTER HEIGHT ADJUSTMENTNUMBER OF 1/4 BLADE SPACERS CUTTING HEIGHT ADJUSTMENT 1 to 4 1/4AXLE NO. OF SPACERS48” Deck Used For Reference Only CUTTER DECK BELT ADJUSTMENTBELT GUIDE LOCATION NOTE These drawings are viewed from underneath engine deckDRIVE BELT TENSION ADJUSTMENT POSITIONS Note Different pressures may make mower cut unevenly 6. TROUBLE SHOOTING6.3 BLADES DO NOT STOP WHEN DISENGAGED 6.1 MOWER PULLING LEFT OR RIGHT32 and 36 MOWER DECK ENGINE TROUBLESHOOTINGENGINE TROUBLESHOOTING TABLE 7. MOWER DECK BELT ROUTING8. WIRING DIAGRAMS 9. WARRANTY Page Description of Work Done SERVICE RECORDService Done By DateFOLD ALONG APPROPRIATE LINE T H I S I S A 5 S L O P ET H I S I S A 1 0 S L O P E T H I S I S A 1 5 OSL P EVIKING HYDRO METRO METRO HP SELF STEERING SULKY GRASS CATCHER MICRO-MULCH ACCESSORYSEE EXMARK’S COMPLETE LINE OF PRODUCTS FOR TURF CARE LAZER Z LAZER Z HP EXPLORER TURF RANGER TURF TRACER TURF TRACER HP