Contents | Exmark Series X guide

Contents
Introduction	3
Safety	5
Safety Alert Symbol	5
Safe Operating Practices	5
Safety and Instructional Decals	11
Specifications	15
Model Numbers	15
Systems	15
Dimensions	17
Torque Requirements	19
Product Overview	19
Operation	20
Controls	20
Pre-Start	23
Operating Instructions	23
Transporting	27
Maintenance	29
Recommended Maintenance Schedule(s)	29
Periodic Maintenance	30
Check Engine Oil Level	30
Check Mower Blades	32
Check Safety Interlock System	33
Check Rollover Protections Systems (Roll
Bar) Knobs	33
Check Seat Belt	34
Check for Loose Hardware	34
Service Air Cleaner	34
Change Engine Oil	34
Check Hydraulic Oil Level	34
Check Tire Pressures	35
Check Condition Of Belts	35
Lubricate Grease Fittings	35
Lubricate Brake Handle Pivot	36
Lubricate Deck Lift Pivot	36
Check Spark Plugs	36
Change Hydraulic System Filter and
Fluid	37
Wheel Hub - Slotted Nut Torque
Specification	37
Check Engine Coolant Level (Kawasaki
Liquid-Cooled Only)	38
Change Engine Coolant (Kawasaki
Liquid-Cooled Only)	38
Check Spark Arrester (if equipped)	39
Thread Locking Adhesives	39
Copper-BasedAnti-seize	40
Dielectric Grease	40
Adjustments	40
Deck Leveling	40

Pump Drive Belt Tension	42
Deck Belt Tension	42
Adjusting the Parking Brake	42
Electric Clutch Adjustment	44
Motion Control Linkage Adjustment	45
Motion Control Damper Adjustment	46
Motion Control Neutral Lock Pivot
Adjustment	46
Motion Control Handle Adjustment	46
Motion Control Full Forward Tracking
Adjustment	47
Caster Pivot Bearings Pre-Load
Adjustment	47
Cleaning	48
Clean Engine and Exhaust System
Area	48
Remove Engine Shrouds and Clean Cooling
Fins	48
Clean Hydro Fan Cooling Fins	48
Clean Debris From Machine	48
Clean Grass Build-Up Under Deck	48
Waste Disposal	49
Troubleshooting	50
Schematics	53

4

Image 4

Exmark Series X manual Contents

Contents

Lazer Z Advantage Series X Models California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices Training Safety Operation Using the Rollover Protection System Rops Slope Operation Maintenance and Storage Safety Safety and Instructional Decals 109-3148 109-7232 109-8483 116-0752 Model Numbers SpecificationsSystems Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting Deck Dimensions Overall WidthOverall Length Overall Height Curb Weight Accessory Weight Table WorksheetTread Width Center to Center of Tires, Widthwise Wheel Base Center of Caster Tire to Center of Drive Tire Product Overview Torque Requirements Operation Controls Ignition Switch Fuel Shut-Off ValveHour Meter Fuel Gauge PTO Engagement Switch Low Voltage IndicatorDrive Wheel Release Valves Do Not tow machine Pre-Start Operating InstructionsDeck Lift Pedal Transport Lock Open the Fuel Shut-Off Valve Starting the Engine Engaging the PTO Disengaging the PTOStopping the Engine Driving the Machine Driving Forward Adjusting the Cutting HeightDriving in Reverse Transporting Adjusting the Anti-Scalp RollersTransporting a Unit Loading a Unit Maintenance Recommended Maintenance Schedules Check Engine Oil Level Check Battery ChargeProposition 65 Warning Recommended Jump Starting Procedure Do Not jump start a weak battery if these conditions exist Check Mower Blades Check Safety Interlock System Check Rollover Protections Systems Roll Bar Knobs Service Air Cleaner Check Seat BeltCheck for Loose Hardware Change Engine Oil Check Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel Hubs Lubricate Brake Handle Pivot Lubricate Deck Lift PivotCheck Spark Plugs Change Fuel Filter Change Hydraulic System Filter and Fluid Wheel Hub Slotted Nut Torque SpecificationStyle a black finish Change Engine Coolant Kawasaki Liquid-Cooled Only Check Engine Coolant Level Kawasaki Liquid-Cooled OnlyStyle B yellow zinc Check Spark Arrester if equipped Thread Locking Adhesives Dielectric Grease Copper-Based Anti-seizeDeck Leveling Adjuster screw Yoke 4 inches 8.3 cm Pump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Start the mower while in the operator position Electric Clutch Adjustment Removing the Shim Motion Control Linkage Adjustment Motion Control Damper Adjustment Motion Control Neutral Lock Pivot AdjustmentMotion Control Handle Adjustment Adjusting the height Caster Pivot Bearings Pre-Load Adjustment Adjusting the Tilt Clean Engine and Exhaust System Area Remove Engine Shrouds and Clean Cooling FinsClean Hydro Fan Cooling Fins Clean Debris From Machine Waste Disposal Battery DisposalMotor Oil Disposal Troubleshooting Problem Possible Cause Corrective Action Refer to Check Engine Coolant Level Troubleshooting Schematics Electrical Diagram Air-Cooled Electrical Diagram Liquid-Cooled TAN Electrical Logic Schematic Air-Cooled Schematics Hydraulic Diagram General Warranty Conditions and Products Covered Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options