Installation, cont’d
E | Audio Input connector — Plug a computer audio source | ||||||||||||||||||
| into this 3.5 mm stereo jack. Wire the connector as shown in | ||||||||||||||||||
| figure | ||||||||||||||||||
| Tip (+) |
|
| Sleeve | |||||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Ring | |||||||||||||||
|
|
|
|
|
|
|
| Tip (+) | |||||||||||
|
|
|
|
|
|
|
|
|
|
| Sleeve ( |
| ) | ||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
| 3.5 mm Audio Plug | |||||||||||||||
| Figure | ||||||||||||||||||
F | Auto Power LED — This LED lights to indicate that a VGA | ||||||||||||||||||
| input cable has been connected to the front panel Computer |
Input connector and the interface has automatically turned itself on.
4
3
5
IMAGE SHIFT CONTROL
OUTPUT SYNC FORMAT (SYNC ON GREEN)
OUTPUT SYNC FORMAT (RGBHV/RGBS)
NO MONITOR AT POWER UP
AUTO POWER DISABLE/ENABLE
2
1
| N The Auto Power LED does not light if pin 10 on the |
| Computer Input connector is not tied to ground. |
| However, if pin 10 is not tied to ground, Auto Power only |
| lights once a video source is connected. |
G | MAAP mounting opening — Mount up to four |
| MAAPs in this opening. For instructions, see "Mounting |
| optional MAAP devices (CIA111 only)", later in this chapter. |
Side Panel Features and Cabling
See figure
A | Sharpness control — Use a screwdriver to turn this control |
|
|
|
|
|
| clockwise to increase the sharpness setting or counterclockwise | |||||
B | to decrease the sharpness setting. |
|
|
|
|
|
Power adapter connection — Plug the included power | + – | |||||
|
| |||||
| adapter into this |
|
|
|
|
|
|
|
|
|
|
| |
| the connector as shown at right. |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| C When you are connecting the power |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| |
| supply, voltage polarity is extremely |
|
|
|
|
|
|
|
|
|
|
| |
| important. Applying power with incorrect |
|
|
|
|
|
| voltage polarity could damage the power supply and | |||||
| the CIA. Identify the power cord positive lead by | |||||
| the red heat shrink wrapping around it. To verify | |||||
| the polarity before connection, check the no load | |||||
| power supply output with a voltmeter. |
|
|
|
|
|
Figure 2-3 — Side panel
C | Audio output connector — Plug the audio output device into | |||
| this | |||
| in figure |
|
| |
| Unbalanced Output | Balanced Output | ||
| Tip | AUDIO L R | Tip | AUDIO L R |
| See Caution | Ring | ||
| Sleeve (s) | Sleeve (s) | ||
| Tip | Tip | ||
| See Caution | Ring | ||
|
|
| ||
| Figure | |||
| N The unbalanced output wiring scheme on this output | |||
|
| connector is different from most other Extron audio | ||
|
| devices. Double check if you are not sure. |
| |
D | Video output connectors — Connect these five BNC connectors | |||
| to the display device’s RGB input. |
|
CIA111 and CIA114 • Installation and Operation | CIA111 and CIA114 • Installation and Operation |