Installation, cont’d
E | Mode Select DIP switches — Set these switches to select | ||
| settings for horizontal position control, sync format, monitor | ||
| emulation, and Auto Power. | ||
| 1 | — Image Shift control | |
|
| On — | The Image Shift button is enabled and shifts |
|
|
| the location of the image when pressed |
|
|
| (default). |
|
| Off — | The Image Shift button is disabled and does |
|
|
| not shift the location of the image when pressed. |
| 2 | — Output sync format (sync on green) | |
|
| On — | The interface outputs RGsB video. |
|
| Off — | The interface outputs RGBS or RGBHV video |
|
|
| (default). See switch 3, on page |
|
|
| between RGBS and RGBHV. |
| 3 | — Output sync format (RGBS or RGBHV) | |
|
| On — | The interface outputs RGBHV video (default). |
|
| Off — | The interface outputs RGBS video. |
| 4 | — No Monitor at Power Up | |
|
| On — | The interface powers up with No Monitor enabled |
|
|
| (default). |
|
| Off — | The interface powers up with No Monitor disabled. |
| 5 | — Auto Power Disable | |
|
| On — | The interface does not power up or down |
|
|
| automatically; it stays on unless you remove power |
|
|
| by disconnecting the power cable. |
|
| Off — | The interface powers up automatically when it |
|
|
| senses an input sync signal, and turns itself off |
|
|
| when the sync signal is removed. |
| 6 | — Not used |
Pre-installation Testing and Troubleshooting
Before installing the interface into the wall or furniture, test the system to verify that the connections and settings are correct.
Apply power to the interface. If an active sync signal is present on the input or if the
If the LED does not light, check the wiring at both the interface and the power supply, and ensure that the power supply is connected to a power source.
If the image does not appear or there is no sound
1. | Make sure that all the devices are powered on. |
2. | Ensure that the connectors are wired correctly at both |
| ends of the cables. Audio cables must be wired for an |
| unbalanced stereo input signal and for a balanced or an |
| unbalanced stereo output signal. |
3. | If input is from a laptop computer and no picture appears, |
| check the computer’s user’s guide or contact Extron to |
| determine if special commands are required to output |
| video to the external video port. Also, many laptops’ |
| screens shut off after the external video port is activated. |
4. | Call the Extron S3 Sales and Technical Support Hotline if |
| the image still does not appear or there is no sound. |
If the image is not displayed correctly
1. | Make sure the correct input and output cables are being |
| used and that they are not damaged. |
2. | Check the DIP switch settings to make sure the interface is |
| putting out the correct sync format. |
3. | If the picture appears and is stable, but it has ghosting |
| or blooming, verify that the video input is properly |
| terminated. If the problem is not resolved by changing the |
| termination, try using a different input cable. Poor quality |
| or damaged cable can cause ghosting or blooming. |
4. | If the picture has a white, ghosted image on the right side |
| of the lines/characters, the sharpness may be set to high. |
| Use a Tweeker or screwdriver to turn the sharpness control |
| counterclockwise. |
5. | If the picture is still not displayed correctly, call the Extron |
| S3 Sales and Technical Support Hotline. |
CIA111 and CIA114 • Installation and Operation | CIA111 and CIA114 • Installation and Operation |