| |
Refer also to the CrossPoint 450 Plus / | CrossPoint / MAV Matrix |
MAV Plus User’s | Switchers |
Manual at www.extron.com | • Remote Control |
. |
|
Command | ASCII command | Response | Additional description |
| (host to switcher) | (switcher to host) |
|
Create ties
N• Commands can be entered
•The matrix switchers support
N When you create a tie where X! = 00, you tie no input to the specified output (X@) (untie X@). When you create a tie where X@ = 00, you untie all outputs from input X!.
NThe & tie command for RGB and the % tie command for video can be used interchangeably.
NThe & read tie command for RGB and the % read tie command for video can be used interchangeably.
Tie input X! to output X@, video | X!*X@! | OutX@•InX!•All] | Tie input X!‘s video and audio to output X@. |
and audio |
|
|
|
Example: | 1*3! | Out03•In01•All] | Tie input 1 video and audio to output 3. |
Tie input X! to output X@, RGBHV | X!*X@& | OutX@•InX!•RGB] | Tie RGB only (video breakaway). |
Example | 10*4& | Out04•In10•RGB] | Tie input 10 RGB to output 4. |
(see 3rd Note, above): |
|
|
|
Tie input X! to output X@, video | X!*X@% | OutX@•InX!•Vid] | Tie video only (video breakaway). |
Example | 7*5% | Out05•In07•Vid] | Tie input 7 video to output 5. |
(see 3rd Note, above) |
|
|
|
Tie input X! to output X@, audio | X!*X@$ | OutX@•InX!•Aud] | Tie audio only (audio breakaway). |
Example: | 24*04$ | Out04•In24•Aud] | Tie input 24 audio to output 4. |
Read RGB output tie | X@& | X!] | RGBHV input X! is tied to output X@. |
Read video output tie | X@% | X!] | Video input X! is tied to output X@. |
Read audio output tie | X@$ | X!] | Audio input X! is tied to output X@. |
|
| ||
N X!= Input number | 00 – (maximum number of inputs for your model) (00 = untie) | ||
X@= Output number | 00 – (maximum number of outputs for your model) (00 = untie all outputs) |
Remote Control, cont’d
Command | ASCII command | Response | Additional description |
| (host to switcher) | (switcher to host) |
|
CrossPoint / MAV Matrix Switchers
Refer also to the CrossPoint 450 Plus / MAV Plus User’s
Video and audio mute commands
RGB/video mute | X@*1B | VmtX@*1] |
RGB/video unmute | X@*0B | VmtX@*0] |
Read RGB/video mute | X@B | X#] |
Global RGB/video mute | 1*B | Vmt1] |
Global RGB/video unmute | 0*B | Vmt0] |
Audio mute | X@*1Z | AmtX@*1] |
Audio unmute | X@*0Z | AmtX@*0] |
Read audio mute | X@Z | X#] |
Global audio mute | 1*Z | Amt1] |
Global audio unmute | 0*Z | Amt0] |
View output mutes | EVM} | X$1, X$2, ... X$n] |
Mute output X@ RGB (video off). Unmute output X@ RGB (video on).
1 = mute on, 0 = mute off. Mute all RGB outputs. Unmute all RGB outputs.
Mute output X@ audio (audio off). Unmute output X@ audio (audio on).
1 = mute on, 0 = mute off. Mute all audio outputs. Unmute all audio outputs.
Each X$ response is the mute status of an output, starting from output 1.
n = the maximum number of outputs for this model.
• Remote Control
EVM} Mut02202000000000000000000000000000]
Output 2, 3, and 5 audio is muted. All other outputs are unmuted.
NThe “Mut” portion of the response appears only when the switcher is in Verbose mode 3. See the Verbose mode command on page
N X@= Output number | 01 – (maximum number of outputs for your model) | |
X#= Mute | 0 = off (unmuted) | |
X$= Video/audio mute: | 1 | = on (muted) |
0 | = no mutes | |
| 1 | = video mute |
| 2 | = audio mute |