Installation, cont’d
Control and power connections
11
Extron
• For a
• For an MLS switcher slaved to an MLC controller, connect a cable from the MLC’s MLS/Power port and from a 12VDC
Once the system has been cabled and set up via the control software and the front panel Aux/Mix adjustment, the MLC or a host computer communicating through the MLC can be used to remotely control the switcher. Refer to chapter four of the MediaLink Controllers User’s Manual and to the MediaLink Control Program help file for details on configuring an
An Extron IR Link infrared repeater cannot be used with the MLS 100 Series switchers. There is no connection for that device’s control signals.
The MLC to which the MLS 100 Series switcher is connected must have MLC firmware version 1.04 or higher. The control/setup software must be version
2.0 or higher. Use one of the following methods to find |
out the version levels of the MLC’s firmware and the |
control software. |
• Connect the MLC’s |
chapter four) of Q to the MLC. The MLC will respond |
with its firmware version. |
• Connect the MLC’s |
the MediaLink control software |
power supply, and tie all the drain wires to the same ground.
(see chapter four), and click on |
Help to display the software |
POWER | MLS100Series |
| Switcher |
A B | |
Power Port |
|
| 1 |
|
|
|
| 2 |
|
|
| 3 |
|
|
|
|
|
|
|
|
|
|
|
| INPUTS |
|
|
|
| OUTPUT |
| |
|
|
|
| AUDIO INPUTS |
|
|
| AUX/MIX |
| OUT | CONTROL/ | ||||
L | 1 | R | L | 2 | R | L | 3 | R | L | 4 | R | MONO | L | R | POWER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| A B |
MLS 103 V |
|
|
|
|
|
|
|
|
| 12V | .5A MAX |
|
|
| MLS 103 V | ||
+12VDC input |
|
| Rear Panel | ||
Ground ( ) |
|
|
| External | |
|
|
|
| Power Supply | |
|
| External |
| 250 ft | |
|
| Power Supply |
| ||
|
|
| (76.2 m) | ||
|
| (12VDC, 1A max.) |
| ||
|
|
| max. | ||
|
|
|
| ||
Ground all devices |
|
|
| ||
+12VDC |
|
|
|
| |
Ground ( ) |
| A B C D E A B C D E | 1A 1B 2A 2B 3A 3B A B C D | 1 2 3 4 5 6 A B | |
| IR |
| Tally Out MLS/Power | ||
| Display/Source Control | Relays IR/RCM | Extron Switcher Control | ||
B Receive (Rx) | Transmit (Tx) B | MLC 206 Bottom Panel | |||
A Transmit (Tx) | Receive (Rx) A | ||||
|
|
|
NOTE If you use cable that has a | MLC 206's | NOTE You must connect a | |
drain wire, tie the drain wire | MLS/Power | ||
ground wire between | |||
to ground at both ends. | Port | ||
| the MLC and MLS. | ||
A B |
|
version, the MLC’s firmware |
version, and the MLS’s |
firmware version as shown in |
the example at right. |
If your MLS’s firmware is an earlier version, contact
Extron to obtain updated firmware.
Setting Up Optimal Audio Gain
Audio input levels and desired output levels vary depending on the types of equipment involved. Before setting the MLS’s per- input gain or attenuation, determine the levels of the input and output equipment. Use the table below as a general guide.
Typical Audio Levels for Various Equipment Types
| Input/Output Levels | |||
| +4dBu 0dBu | |||
|
|
| ||
Professional line level audio equipment X | X |
|
|
Connecting an MLC 206
MLS / Power
Equipment Categories | Consumer audio equipment (VCRs, DVDs, | X | X |
|
to a MediaLink VersaTools Switcher and an external power supply
laptop computers, portable audio devices) |
MediaLink VersaTools Switchers • Installation | MediaLink VersaTools Switchers • Installation |