Extron electronic setup guide Rear Panel Features - MLS 608 D and MTP HDMI U R,    ,   

MLS 608 D Series • Setup Guide

The Extron MLS 608 D Series are eight input, multi-format AV switchers with ProDSP™ audio and are able to integrate analog and digital sources. There are three models:

• MLS 608 D (with variable preamp output - no amplifier)

•MLS 608 D MA (with 40 watt 70 volt mono power amplifier)

•MLS 608 D SA (with 2 x 20 watt stereo power amplifier)

This guide allows you to easily and quickly setup and configure your MLS 608 D using step by step instructions. It covers performing basic operations using the front panel controls and selected Simple Instruction Set (SIS™) commands.

It also gives connection information for the MTP HDMI U R twisted pair receiver, which is supplied with the MLS 608 D Series unit. See rear cover for a diagram of a typical MLS 608 D application, showing the MLS 608 D SA model.

NOTE: For full installation, configuration, and operation details for all MLS 608 D models, see the MLS 608 D Series User Guide, and for complete details on the MTP HDMI U R, see the MTP HDMI U R User Guide, both available at www.extron.com.

Rear Panel Features — MLS 608 D and MTP HDMI U R

NOTE: The MLS 608 D SA, as shown below, is representative of the MLS 608 D Series. It has the maximum number and type of connectors and features of the three models. The MLS 608 D model lacks the power amplifier output.

MLS 608 D SA	3
CONFIGURABLE ANALOG INPUTS
100-240V 50/60 Hz
1
	BUFFERED OUTPUT
2	3

1.2A MAX

6

	DIGITAL INPUTS		AUDIO INPUTS
ANALOG OUTPUT	L	1 R	L 2 R	L 3 R

MTP

5

6

DIGITAL OUTPUT

+

AUDIO

1

2

+12 V OUT

7

8

L

5

R

L

6

R

L

7

R

L

8

R

4 (MTP)

VIDEO + RS-232

PWR OUT=

12W

14

MLS 608 D SA

RS-232 INSERT

			Tx Rx	N/A N/A
		AUDIO OUTPUTS
1MIC/LINE 2	+ 48V	4/8 OHM - 20W x 2		+12V
		L 1 R L 2 R	Tx Rx

1

2

RS-232

HOST

PWR OUT = 7.2 W

1

2 4 5

7 8 9 10 11 12 13

Power, Analog, and Digital Connections

A AC power connector

B RGB, component/S-video/composite inputs: 15-pin HD connectors (inputs 1-3, see rear page for pinout details)

C Buffered output: 15-pin HD connector (tied only to input 1)

D Universal MTP RJ-45 connector (input 4, see rear page for pinout details)

E 12 V output MTP/HDMI U R power source: 2-pole captive screw connector

F Analog video and audio MTP output: RJ-45 connector

G Digital inputs: HDMI connectors (inputs 5-8)

H Digital video and RS-232 outputs: RJ-45 connectors

Audio and RS-232 Connections

I Audio inputs: 5-pole captive screw connectors (inputs 1-3, 5-8)

J Mic/line level audio inputs (1-2): 3-pole captive screw connectors and phantom power LEDs

K Line level audio output: 5-pole captive screw connectors (audio outputs 1-2)

L Power amplifier output connector (MA and SA units only)

M RS-232 control/configuration port and +12 V power output (for optional MLC power source): 5-pole captive screw connector

N RS-232 insertion pass-through port: 5-pole captive screw connector

MTP/HDMI U R

DIGITAL INPUT		DIGITAL OUTPUT
1	2		R-Y
POWER
12V		HDMI	RS-232
0.8A MAX			PASS THRU

Tx Rx

A B C D

	K	J	I
		RS-232
Y	B-Y	Tx Rx	SPARE
		VID
		MONO AUDIO
		1	2
	RGB	Y/C
MTP INPUT		ANALOG OUTPUTS
E	F	GA	H









Power input

Digital signal inputs (1 and 2)

Digital (HDMI) output

RS-232 pass-through connector









MTP input

RGBHV, RGBS output*

S-video output*

Mono audio output







RS-232 port (analog side), not used in MLS 608 D system

Composite video output*

Component video (R-Y, Y, B-Y) output*

* = Analog outputs

1