MLS 608 D Series • Setup Guide (Continued)
Front Panel Features
All models have the following front panel features:
R CONFIG
|
|
| SOURCE SELECTION |
|
|
| |
PC | DOC |
| AUX | LAPTOP |
|
| |
CAM |
| VID |
|
| |||
|
|
|
|
|
| ||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
VOLUME | MIC VOLUME |
|
|
|
|
|
|
|
|
| MLS 608 D |
|
|
|
|
|
|
|
| AV Switcher | with ProDSP™ |
|
|
|
|
|
| 5 |
|
| |
|
|
|
|
|
|
|
|
| |
1 | 2 | 3 | 4 | 6 | |||||
| A Power/reset status LED |
|
| D Input selection buttons (8) |
|
| |||
| B Reset button (recessed) |
|
| E Program volume control (adjustment knob) | |||||
| C USB configuration port |
|
| F Mic volume control (adjustment knob) |
|
|
Front Panel Operation
NOTE: For operation details for all models, see the MLS 608 D Series User Guide, available at www.extron.com.
A Power/reset status LED — This LED lights green when power is applied, and amber when in standby mode. It also indicates the reset mode when the reset button is being operated (see below).
B Reset button — In order to reset the MLS switcher to one of two available reset modes via the front panel, press and hold this recessed button in and observe the LED for confirmation of unit resetting.
Reset Mode 1, Use factory firmware — To reset temporarily to the factory default firmware, press and hold the reset button in while applying power to the unit.
NOTES: • After a Mode 1 reset, update the firmware to the latest version. DO NOT use the factory firmware resulting
from the reset. Factory firmware must be
• If you do not want to update the firmware, recycling the power reinstates the firmware version used before
the Mode 1 reset.
Reset Mode 5, Reset to factory default — To reset the device to factory defaults (with the exception of the firmware), press and hold in the reset button for approximately 9 seconds, until the LED blinks three times (once at 3 seconds, 6 seconds, and 9 seconds), and then release.
Within 1 second press and release the reset button once (<1 second). Nothing will happen if the momentary press is not made within 1 second.
C Front panel mini USB configuration port — Connect a computer to this port, using a mini USB cable (not supplied), for configuration, control, and firmware upgrades.
NOTE: For details of device configuration via software, SIS commands, and firmware updating for all models, see the
DSP Configurator Help file or the MLS 608 D Series User Guide, both available at www.extron.com.
D Source selection buttons — Use these buttons to select or switch between inputs. The button lights amber to indicate which input is active.
E Program volume adjustment knob — Use this to set or adjust the program output |
| LED equivalent | |
VOLUME | dB value | ||
volume (attenuation, from | |||
| |||
| |||
level (all off at |
| ||
|
| ||
volume, |
| ||
F Mic volume adjustment knob — Use this knob to set or adjust the volumes of the two |
| ||
| |||
mic inputs (see page 1, J ) as desired. The LEDs indicate the volume level. |
| ||
Rotate the knob clockwise to increase volume, counterclockwise to decrease volume. |
| ||
NOTE: The system and microphone volume settings and adjustments |
| ||
| - 69 to | ||
can be made using Extron DSP Configurator program or via SIS |
| ||
|
| ||
commands. See the MLS 608 D User Guide for details. |
| ||
|
|
6