Faber Dama Isola installation instructions Tools Needed For Installation

The ductrun should not exceed 35 equivalent 45˚ Elbow feet if ducted with the required minimum of 6" 90˚ Elbow roundduct.Calculatethe lengthofthe ductwork 90˚ Flat Elbow by adding the equivalent feet in FIGURE 2 for Wall Cap each piece of duct in the system. An example

is given in FIGURE 3.

UNPACK THE RANGEHOOD

FIGURE 1

TOOLS NEEDED FOR INSTALLATION
• Saber Saw or Jig Saw
• Drill
• 1 1/4" Wood Drill Bit
• Pliers
• Phillips Screwdriver
• Flat Blade Screwdriver
• Wire Stripper or Utility Knife
• Metal Snips
• Measuring Tape or Ruler
• Level
• Pencil
• Caulking Gun	RANGEHOOD COMPONENTS
• Duct Tape
PARTS SUPPLIED FOR INSTALLATION	A. CANOPY SECTION
• 1 Hardware Package	B. LOWER CHIMNEY COVER
• 1 Literature Package	C. UPPER CHIMNEY COVER
PARTS NEEDED FOR INSTALLATION	D. CHIMNEY COVER SCREWS
	E. CANOPY SCREWS
• 2 Conduit Connectors	F. CHIMNEY SUPPORT
• Power Supply Cable	G. WOOD SHELF BOLTS
• 1 Wall or Roof Cap	H. WOOD SHELF WASHERS
• All Metal Ductwork	I. WOOD SHELF NUTS
OPTIONAL ACCESSORIES AVAILABLE	J. PLUGS - DO NOT USE
	K. MOUNTING TEMPLATE
• High Ceiling Chimney Kit	L. CONNECTOR BOX SCREWS
Extends the island chimney for high	M. CONNECTOR BOX HALVES
ceilings	N. DAMPER
part # 620000370 - Stainless

•*Ductless Conversion Kit For non-vented installations only

* it is highly recommended that professional style cooking always be vented to the outside

part # 620000364 - Stainless

• Replacement Charcoal Filter For non-vented installations only, replace charcoal filter as needed part # 620000041

Remove the rangehood from the carton and place on a flat surface for assembly. Before discarding the packaging, check to make sure that no mounting hardware or parts are missing. DO NOT REMOVE THE PLASTIC COVERING ON THE CHIMNEYS AT THIS TIME! This plastic covering protects the chimney from scratches during installation.

For safe packaging, the entire chimney section of the hood is shipped assembled. It must be disassembled completely for installation. Disassemble packaged chimney components by sliding apart the chimney covers (B and C in FIGURE 1). Remove the LOWER CHIMNEY COVER (B) from the CHIMNEY SUPPORT (F) by removing the 2 philips screws on the outside bottom of the chimney cover. Remove the UPPER CHIMNEY COVER (C) from the CHIMNEY SUPPORT (F) by removing the 2 philips screws on the outside top of the chimney cover.

PREPARING TO ATTACH THE CHIMNEY		CALCULATE THE DUCTRUN LENGTH
The rangehood attaches to the ceiling by a
metal support structure (D in FIGURE 1). This
support must be attached to the ceiling before
the canopy is attached. This structure must
be firmly attached to the ceiling.
FOR WOOD CEILINGS: Use four 4" long		For best results, use no more than three 90°
wood screws and washers.
FORPLASTERORSHEETROCKCEILINGS:		elbows. Make sure that there is a minimum
If possible, the support must be attached to		of 24" of straight duct between elbows if
the ceiling joists. If not, a supporting structure		more than one is used. Do not install two
behind the sheet rock must be built.		elbows together. If you must elbow right
FOR WOOD SHELVES:	Use items G, H, &	away, do it as far away from the hood's
I in FIGURE 1.		exhaust opening as possible.

	3.0 feet
	5.0 feet
	12.0 feet
FIGURE 2	0.0 feet
9 Feet Straight Duct	9.0 feet
2 - 90˚ Elbows	10.0 feet
Wall Cap	0.0 feet
Total System	19.0 feet
FIGURE 3

Version 1/06 - Page 4